Primera Technology LX900 user manual Printing History

Page 2

Notices: The information in this document is subject to change without notice. NO WARRANTY OF ANY KIND IS MADE WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No liability is assumed for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without prior written consent.

Trademark Acknowledgments: Windows is a registered trademark of Microsoft Corporation. All other trademarks are the property of their respective owners.

Printing History

Edition 3.0, #062211, Copyright 2010, All rights reserved.

FCC Compliance Statement: This device complies with part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For Users in the United States: This product is intended to be supplied by a UL listed Direct Plug-In Power Supply marked "Class 2"or a UL listed ITE Power Supply marked "LPS" with output rated 12VDC, 4.5A or higher. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Re-orient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cables is required to comply with the Class B limits of Part 15 of the FCC Rules. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate and/or obtain warranty service for this equipment.

For Users in Canada: This digital apparatus does not exceed the Class B limits for radio noise for digital apparatus set out on the Radio Interference Regulations of the Canadian Department of Communications. Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la class B prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada.

Product Disposal

Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.

Battery Notice

This product contains Perchlorate material. Special handling may apply. For more information, go to http://www.dtsc.ca.gov/hazardouswaste/perchlorate/

CAUTION!

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE EXTERIOR PANELS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. OPERATE THE UNIT WITH ONLY THE PROPER ELECTRICAL SPECIFICATIONS AS LABELED ON THE PRINTER AND AC ADAPTER.

CAUTION!

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

ii

Image 2
Contents 062211-511271 All rights reserved Printing History Table of Contents Interactive Feature Choosing a Good Location Getting StartedThank YOU… Unpacking and Inspection Identifying the Parts Computer Specifications Recommended PC SpecificationsLabel and Roll Specifications Label StockTOC Index Label Side Out Roll O.D Installing Label Stock Roll Guide Movable Throat Guide Fixed Throat Guide Adjusting the Label Stock TOF TOP of Form Sensor Circular LabelsThrough-Hole Labels SET the Stock Sensor Mode SET the Output Mode TOC Ink Cartridges Status Monitor Monitoring INK Levels Using the Cost Estimator Replacing INK Cartridges / LOW INK Warning TOC TOC Using Nicelabel PrintingTOC TOC TOC TOC TOC Creating Barcodes in Nicelabel RSS TOC Printing from Other Programs Adjusting Print Alignment TOC Creating a Full Bleed Print Printer Driver Settings To find Driver Settings Paper Size Portrait LandscapeColor Matching Ink Saturation Image is Vertically Offset Troubleshooting and MaintenanceSolving Print Alignment Problems Image is printing horizontally offset Solving Print Quality Problems Maintenance Station Color Matching and Design Tips DPI Image printed with the LX900 TOC Cleaning the Printer Create a Support ReportCleaning the Printhead 3B. Deep clean the cartridge 3C. Preventing clogged nozzlesPrinthead / Cartridge Replacement Procedure Semi-Permanent Print Head Part NumberReplacing the Printhead Ink Feed Unload Press Pause + Load/Feed to Start and FinishTOC Now align the print head as described in B Technical Support Interpreting the PRINTER’S Indicator LightsExplanation Source LocationSection Technical Specifications Media TypesIndex DPI11, 33, 35