Star Micronics 4000 user manual Safety Notices for Finland

Page 2

Safety Notice

This printer is certified as a Class 1 laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968. This means that the printer does not emit hazardous laser radiation.

Since radiation emitted inside the printer is completely confined within protective housings and external cov- ers, the laser beam cannot escape from the machine during any phase of user operation.

The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration imple- mented regulations for laser products on August 1, 1976. These regulations apply to laser products marketed in the United States. The label on the printer indicates compliance with the CDRH regulations and must be attached to laser products marketed in the United States.

Caution-use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Federal Communications Commission

Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica- tions. However, there is no guarantee that interference will not occur in a particular installation. If this equip- ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Unauthorized modifications of this product by the user will void his authority to operate the equipment unless expressly approved by the party responsible for compliance.

For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable. The above statement applies only to printers marketed in the U.S.A.

Statement of

The Canadian Department of Communications

Radio Interference Regulations

This digital device does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n'emen pas de bruits radioélectriques dépassant les limits applicable aux appareils numériques de la classe B prescrites dan le Règlement sur le brouillage radioélectrique édicté par le minisère des Communications du Canada.

The above statement applies only to printers marketed in Canada.

Safety Notices for Finland

Tämä Kirjoitin LUOKAN 1 LASERLAITE.

VAROITUS! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.

DENNA SKRIVARE ÄR EN KLASS 1 LASERAPPARAT.

VARNING! Om apparaten används på annat sätt än i denna bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laseklass 1.

The above statement applies only to printers marketed in Finland.

Image 2
Contents WinType Safety Notice Safety Notices for FinlandBescheinigung des Importeurs Trademark AcknowledgmentsContents Iii Specifications Character tables for PCL mode Star WinType Printer Status DisplaySystem requirements IntroductionWord about the printer Maintenance & troubleshooting Setting up your printerInstalling the printer driver software and TrueType fonts Selecting print mediaHow to use this manual Features of the printerPrinter components Placing the printer Setting up your printerUnpacking and checking the package contents Drum Installing the toner cartridgeSteps RollerPage Guides Setting up the upper paper trayPaper Output tray Output paper extender Setting up the output trayConnecting the printer to the computer Turning the printer OFF Connecting the power cordTurning the printer on StepRelocating the printer Page Page Page Recommended print media Type Size Weight/RecommendedSelecting print media Printing media to avoid AcceptableNot AcceptablePage Page Loading envelopes Yesno Installing the printer driver and TrueType fonts Printer command languages Page Installing the printer driver and TrueType fonts MB for all 35 TrueType fonts Printer driver will run properly when you start Windows Page Removing the printer driver software PCL mode Windows Direct GDI modePostScript mode Printing with WinTypeFeatures of the printer driver software Printing with the Windows Direct GDI modePage Page Manual duplex printing If the Print Instruction Page is not checked, click this boxDuplex printing errors Using fonts in the Windows Direct GDI modeEliminating screen fonts from your application Printing with the PostScript mode Printing from a Windows applicationFonts in PostScript Mode Original PostScript Font Name TrueType SubstituteOriginal PostScript Font Name TrueType Substitute PIF File Method Printing DOS applications in PostScript mode under WindowsDOS Prompt Method Printing with the PCL mode Printing in PCL mode from a Windows applicationPrinting DOS applications in PCL mode under Windows Page Fonts in PCL Mode Keyboard Method Mouse MethodSaving download fonts and macros in the PCL mode Page Star WinType Print Manager Enabling the WinType Print ManagerIf the Use WinType Print Method Two Viewing and accessing the WinType Print ManagerMethod One Priority BeepsDisplay Print Status Toner Saving ModePower Saving Mode Smoothing OnSearch for Help On ContentsHow to Use Help AboutSize Job NameFormat TimeChanging priority in the queue Status Bar Progress BarAdd Star WinType 4000 PCL onClick on the Pause button Click on the Add button Page Steps Print Manager window Page Selecting the Printer Status Display Windows Direct GDI mode Star WinType Printer Status DisplayPage Click on Display Print Status with your mouse Double-click on the Star Animate Icon Animate window Status Display Messages JobPicture of your printer Status Display Message Window Cover OpenPrinting Power Off or Cable ProblemNV-RAM Error Fuser AbnormalityDelete PauseResume Maintenance & troubleshooting Maintaining your printerCleaning your printer Cleaning the output port windowClearing paper jams Cartridge compartmentJammed paper Page Faded print Troubleshooting Solving print quality problemsSymptom Possible Cause Action Black dotsBlack Repetitive defectsCharacter voids Blank Partial deletionsWrinkled or blurred Vertical deletionsOther mechanical problems Specifications Reference informationPower specifications Environmental SpecificationsSoftware Reliability specificationsController Paper sizeFonts Original PostScript Font TrueType SubstituteCharacter tables for PCL mode PC-8 Symbol Set PC-8 D/N Danish/Norwegian Symbol Set PC-850 Symbol Set ISO Substitution Table Glossary Default CommandConfiguration Character setFloppy disk FileFile menu FontPortrait ParityPoint PostScriptSymbols IndexSee also PCL mode RAM Customer service information Customer response