Teac X-01 D2 owner manual Troubleshooting, Unlck

Page 25

Troubleshooting

In case you experience any problem with this unit, please take the time to look through this chart and see if you can solve the problem yourself before you call your dealer.

No power

eCheck the connection to the AC power supply. Check and make sure the AC source is not a switched outlet and that, if it is, the switch is turned on. Make sure there is power to the AC outlet by plugging another item such as a lamp or fan.

ePress the POWER button of the main unit to turn it on.

Remote control doesn’t work.

ePress the POWER button of the main unit to turn it on. eIf the batteries are dead, change the batteries.

eUse remote control unit within the range (7m / 23ft.) and point at the front panel.

eClear obstacles between the remote control unit and the main unit.

eIf a strong light is near the unit, turn it off.

Severe hum or noise is heard.

ePlace the unit as far away from a TV as possible.

eMake sure the line cords and speaker cables are as far away from the AC supply as possible.

Will not play.

eReload the disc with the label side UP.

eThis unit cannot play such discs as CD-ROMs. Use a playable disc.

eIf the disc is dirty, clean the surface of the disc.

eA blank disc has been loaded. Load a prerecorded disc.

eIf the unit is condensed, leave the unit for one or two hours with the power turned on.

eIf another operation is still in process, wait a moment and try again.

Sound skips.

ePlace the unit on a stable place to avoid vibration and shock. eIf the disc is dirty, clean the surface of the disc.

eDon’t use scratched, damaged or warped discs.

There is no sound or only a very low-level sound is heard. eCheck that the amplifier and speakers are connected

securely.

eCheck the operation of the amplifier. eCheck the audio output setting.

eWhen the amplifier is connected via the i.LINK (AUDIO) or the DIGITAL OUT terminal, set the Digital Out setting to “ON”.

eThe sound is muted during pause. Press the PLAY button to resume normal playback.

No multi-channel audio output. eSet the Analog Out to “Multi ch”.

eChange the speaker configuration if necessary.

eSuper Audio CDs may have more than one playback area, not all of which contain multi-channel audio data. Choose a multi-channel area.

Overall volume is low, or balance between speakers is strange.

eA speaker’s level (or that of a pair of speakers) has been set up too low or too high in the speaker setup. Correct the

levels.

 

The speaker settings are ignored.

 

eSet the Analog Out to “Multi ch”.

 

eSet the CD Direct to “Normal”.

 

No digital audio output.

 

eCheck that the Digital Out setting is set to “ON”. When using

 

the i.LINK (AUDIO) terminal, set the i.LINK output setting to

 

“60958” or “PCM”.

 

eDigital audio from a Super Audio CD cannot be output from

 

 

the DIGITAL OUT terminals. Use the i.LINK (AUDIO) terminal.

ENGLISH

Word!”

The MODE button flashes, and the display shows “No

 

eThe word sync mode is selected, but there is no clock

 

source. Turn the word sync mode off.

 

 

eNo word clock is being received. Check cables, connections,

 

and settings of the clock generator.

 

The MODE button flashes, and the display shows “WRD

 

UNLCK!”

 

eInvalid word sync signal is received. Check the setting of the

 

clock generator.

 

If normal operation cannot be obtained, unplug the power

 

cord from the outlet and plug it again. This resets the

 

internal micro-computer which can be disturbed during

 

electrical storms, power interruptions, et cetera.

 

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 01 D2 For U.S.A Important Safety InstructionsContents Features Before Use Type of Discs That Can be Played on This System DiscsFollowing discs cannot be played with this unit Restoring factory settings Remote Control UnitHow to insert the batteries Connection Signal GND connection Word sync connectorPower cord receptacle Analog audio output terminalsFront Panel Front panel featuresDisplay Understanding the remote control unit Playback Pausing playbackStopping playback Opening and closing the traySelecting a track Skipping playbackFast scanning Selecting the playback areaClearing the last track from the list Programmed playbackAdding tracks to the list Clearing the whole programDisplay dimming Repeat modeTrack repeat Disc repeatWord DAC Layer Changing the display modeDAC D/A converter Word Word syncDSD Link Layer priority playback areaSacd PCMExit the setup menu by pressing Setup once more Settings introductionUse the cursor buttons to navigate the menus Settings Setup Menu Chart Analog output Analog Out Settings Audio SetupDigital output DigitalOut CD DirectLarge Speaker Size SP SizeSmall On subwoofer onlySpeaker distance Distance This setup is effective in the following case onlySpeaker levels SP Level Test tone length Test toneLink Ieee How to connect multiple i.LINK-capable devicesCopyright protection system Dtcp Data transfer rateUnlck TroubleshootingSpecifications Pour l’Europe SommaireMise au rebut de votre ancien appareil Moteur sans noyau avec aimants néodyme CaractéristiquesAvant utilisation Types de disques lisibles par ce système DisquesCD audio Propos des CD-R/CD-RWRemplacement des piles TélécommandeRestauration des réglages d’usine Comment insérer les pilesConnexions Prises de sortie audio analogique Connexion Signal GNDPrises de sortie audio numérique Prise i.LINK AudioFace avant Description de la face avantAfficheur Touches curseur et Enter Comprendre la télécommandePavé numérique Mise en pause de la lecture LectureArrêt de la lecture Ouverture et fermeture du tiroirSélection d’une plage Saut de lectureRecherche rapide Sélection de la zone de lectureEffacement de la dernière plage de la liste Lecture programméeAjout de plages à la liste Effacement de toute la programmationAtténuation de l’afficheur Mode Repeat lecture en bouclePlage en boucle Disque en boucleChangement du mode d’affichage DAC Convertisseur N/A Word Synchro WordREF. Référence Bit MultibitLayer zone à lecture prioritaire Réglages introduction Encore sur SetupUtilisez les touches curseur pour naviguer dans les menus Réglages Tableau du menu de configuration Sortie analogique Analog Out Réglages Configuration audioSortie numérique DigitalOut On caisson de graves seulement Taille d’enceinte SP SizeNiveaux des enceintes SP Level Distance des enceintes DistanceDurée de la tonalité de test Test tone Sélectionnez « Test Start » et appuyez sur la toucheTaux de transfert des données Système de protection de droits d’auteurComment connecter plusieurs appareils compatibles i.LINK Connexion en guirlandeUNLCK! » Guide de dépannageSpécifications Inhalt Kernloser Motor mit Neodym-Magneten AusstattungsmerkmaleStabiles Chassis mit drei punktgelagerten Standfüßen Audio-DACs Unübertroffene AusstattungsmerkmaleWord Clock Synchronisation Lieferumfang Vor der ersten InbetriebnahmeHinweise zur Verwendung dieser Bedienungsanleitung Vor der ersten InbetriebnahmeAchtung Aufstellen des X-01 D2Allgemeines zu CD-R/CD-RWs Zur Wiedergabe mit dem X-01 D2 geeignete Disc-FormateAchtung WarnungAnfassen einer Disc Anschlüsse Analoge Audioausgänge Signal GND SignalmasseanschlussDigitale Audioausgänge LINK-Schnittstelle AudioEinsetzen von Batterien FernbedienungBatteriewechsel Vorsichtsmaßnahmen im Umgang mit BatterienDAC-Anzeige Bedienelemente auf der GerätevorderseiteFernbedienungssensor Display Disc-Schublade und VerschlussZifferntasten Verwenden der FernbedienungPlay Area Wiedergabebereich Cursor-Tasten und EnterDisplay Unterbrechen der Wiedergabe Pause WiedergabeBeenden der Wiedergabe Öffnen und Schließen der Disc-SchubladeAuswählen eines Musiktitels Verwenden der SKIP-TastenSchneller Suchlauf Löschen des letzten Titels einer Liste Wiedergabe einer programmierten TitelfolgeTitel zu einer Liste hinzufügen Löschen einer kompletten TitelfolgeEinstellen der Display-Helligkeit WiedergabewiederholungWiedergabewiederholung von Musiktiteln Wiedergabewiederholung aller TitelNormalanzeige Ändern der DisplayanzeigeREF. Referenz DAC D/A-WandlerBit 1-Bit Layer bevorzugter Wiedergabebereich Einstellungen Einleitung Einstellungen Setup-Menü-Diagramm Analogausgang Analog Out Einstellungen Audio SetupDigitalausgang DigitalOut Large groß Abmessungen der Lautsprecherboxen SP SizeSmall klein On nur SubwooferAbstand der Lautsprechersysteme zur Hörposition Distance Dauer des Testtonsignals Test toneLautsprecher-Wiedergabepegel SP Level Datenübertragungsrate Kopierschutzsystem DtcpAnschließen mehrerer i.LINK-kompatibler Komponenten HinweiseTechnische Daten Hilfe bei Funktionsstörungen Pflege und Wartung Vermeiden Sie KondensationsbildungTeac Esoteric Company

X-01 D2 specifications

The Teac X-01 D2 is a premier audio component that has garnered attention among audiophiles and music enthusiasts. Designed with a keen focus on sound quality and advanced technology, it is celebrated for its exceptional playback capabilities and versatile features.

At its core, the Teac X-01 D2 is a high-end CD player that seamlessly combines modern digital advancements with classic analog design principles. It features a high-precision, slot-loading disc mechanism that not only enhances the convenience of use but also contributes to minimized vibrations during playback. This ensures that the audio signal remains clean and unaffected, resulting in superior sound quality.

One of the standout features of the X-01 D2 is its Dual-DAC architecture, utilizing two high-performance Digital-to-Analog Converters. This design allows for greater detail and dynamic range in audio playback, providing listeners with a rich and immersive experience. The unit supports various audio formats, including standard CDs, as well as high-resolution audio files, ensuring that users can enjoy their music in the utmost fidelity.

The incorporation of TEAC's proprietary technologies also elevates the performance of the X-01 D2. The Ultra-Linear Circuitry minimizes noise and distortion, while the high-quality, low-jitter clock circuitry ensures accurate signal processing. As a result, the audio produced is remarkably clear and precise, showcasing the nuances in even the most complex musical pieces.

Additionally, the Teac X-01 D2 includes multiple digital outputs, allowing users the flexibility to connect to a range of audio systems. These outputs include AES/EBU, coaxial, and optical connections, making it compatible with various audio equipment. The unit also features an analog output, providing connection options for those who prefer a classic analog connection to their amplifiers.

User-friendly controls and an intuitive interface further enhance the overall experience with the X-01 D2. Users can easily navigate through their music collection, adjusting settings and playback modes with ease. Its sleek design, complemented by a high-quality build, ensures that it fits seamlessly into any audio setup, both aesthetically and functionally.

In summary, the Teac X-01 D2 stands as a testament to the brand's commitment to quality and innovation. With its advanced technologies and features, it delivers an unparalleled listening experience that is sure to satisfy even the most discerning audio enthusiasts.
Top Page Image Contents