Teac X-01 D2 Analog audio output terminals, Digital audio output terminals, Link Audio terminal

Page 9

CAUTION:

<Switch off the power to all equipment before making connection.

<Read the instructions of each component you intend to use with this unit.

<Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the signal interconnection cables together with the AC power cord or speaker cables.

AAnalog audio output terminals

2 channel (FRONT)

Use either the XLR or RCA (pin) FRONT terminals for analog stereo output.

If your amplifier has balanced XLR analog audio inputs, connect the XLR jacks on the unit to the amplifier’s XLR jacks, otherwise use the RCA (pin) connections.

5.1 channel

For surround (5.1) amplifiers with analog inputs, also use the RCA (pin) SURROUND pair, CENTER and SUBWOOFER connections (in addition to the FRONT pair).

<If you are connecting only 2 channels, use the 2CH/MULTI button on the remote control to select “2 ch”. For surround sound with six speakers connected, you can select either “2ch” or “5.1 ch” mode. Note that if multi-channel program material is played and 2-channel mode is selected, the multi-channel material will be down mixed to two channels, and output through the L and R front outputs.

BDigital audio output terminals

Digital audio from CD is output from these terminals.

The unit may be connected using either coaxial or optical (TOS) commercially available cables to amplifiers, or to digital audio devices such as CD recorders, etc.

COAXIAL: Use RCA (pin) digital audio cable

OPTICAL: Use optical digital audio cable (TOS)

<The optical terminal is covered by a shutter. Make sure that the cable is firmly inserted, but do not force the cable when connecting it or removing it, in order not to cause damage to the unit.

<The DIGITAL OUT terminals cannot output the digital audio from Super Audio CDs.

Ci.LINK (AUDIO) terminal

In addition to the digital audio from CD, the digital surround audio from Super Audio CDs can be output from this terminal. To enjoy surround sound from a Super Audio CD, connect the i.LINK (AUDIO) terminal to a suitably equipped surround sound amplifier.

Use a commercially available S400 compatible i.LINK (IEEE1394) 6pin cable to connect the unit to an amplifier.

<When using this terminal, set the Digital Out to “ON”, and the i.LINK output setting to “60958” or “PCM” (see pages 21, 16-18).

<See page 24 for further details on i.LINK.

 

 

ENGLISH

D

Word sync connector

 

 

This allows the use of an externally-generated word clock

 

 

connection, using a commercially available BNC coaxial

 

 

cable.

 

 

Devices producing such a suitable clock signal include

 

 

external D-A converters, or dedicated word clock

 

 

generators. Connect the SYNC OUT (or WORD OUT) of such

 

 

a device to the unit.

 

ESIGNAL GND connection

Use a commercially available PVC-covered cord to connect the signal ground terminal on the unit to the amplifier signal ground.

<Note that this is NOT an electrical safety ground (earth).

FPower cord receptacle

Connect the power cord to the power cord receptacle and connect the power plug to an AC wall outlet after all other connections have been made.

<Use only the supplied Esoteric power cord. Use of other power cords may result in fire or electric shock. Unplug the power cord when you are not going to use the unit for an extended period of time.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 01 D2 For U.S.A Important Safety InstructionsContents Features Before Use Discs Type of Discs That Can be Played on This SystemFollowing discs cannot be played with this unit Remote Control Unit Restoring factory settingsHow to insert the batteries Connection Signal GND connection Word sync connectorPower cord receptacle Analog audio output terminalsFront panel features Front PanelDisplay Understanding the remote control unit Playback Pausing playbackStopping playback Opening and closing the traySelecting a track Skipping playbackFast scanning Selecting the playback areaClearing the last track from the list Programmed playbackAdding tracks to the list Clearing the whole programDisplay dimming Repeat modeTrack repeat Disc repeatWord DAC Layer Changing the display modeWord Word sync DAC D/A converterDSD Link Layer priority playback areaSacd PCMSettings introduction Exit the setup menu by pressing Setup once moreUse the cursor buttons to navigate the menus Settings Setup Menu Chart Analog output Analog Out Settings Audio SetupDigital output DigitalOut CD DirectLarge Speaker Size SP SizeSmall On subwoofer onlySpeaker distance Distance This setup is effective in the following case onlySpeaker levels SP Level Test tone length Test toneLink Ieee How to connect multiple i.LINK-capable devicesCopyright protection system Dtcp Data transfer rateUnlck TroubleshootingSpecifications Sommaire Pour l’EuropeMise au rebut de votre ancien appareil Moteur sans noyau avec aimants néodyme CaractéristiquesAvant utilisation Types de disques lisibles par ce système DisquesCD audio Propos des CD-R/CD-RWRemplacement des piles TélécommandeRestauration des réglages d’usine Comment insérer les pilesConnexions Prises de sortie audio analogique Connexion Signal GNDPrises de sortie audio numérique Prise i.LINK AudioDescription de la face avant Face avantAfficheur Comprendre la télécommande Touches curseur et EnterPavé numérique Mise en pause de la lecture LectureArrêt de la lecture Ouverture et fermeture du tiroirSélection d’une plage Saut de lectureRecherche rapide Sélection de la zone de lectureEffacement de la dernière plage de la liste Lecture programméeAjout de plages à la liste Effacement de toute la programmationAtténuation de l’afficheur Mode Repeat lecture en bouclePlage en boucle Disque en boucleChangement du mode d’affichage DAC Convertisseur N/A Word Synchro WordREF. Référence Bit MultibitLayer zone à lecture prioritaire Encore sur Setup Réglages introductionUtilisez les touches curseur pour naviguer dans les menus Réglages Tableau du menu de configuration Réglages Configuration audio Sortie analogique Analog OutSortie numérique DigitalOut On caisson de graves seulement Taille d’enceinte SP SizeNiveaux des enceintes SP Level Distance des enceintes DistanceDurée de la tonalité de test Test tone Sélectionnez « Test Start » et appuyez sur la toucheTaux de transfert des données Système de protection de droits d’auteurComment connecter plusieurs appareils compatibles i.LINK Connexion en guirlandeUNLCK! » Guide de dépannageSpécifications Inhalt Ausstattungsmerkmale Kernloser Motor mit Neodym-MagnetenStabiles Chassis mit drei punktgelagerten Standfüßen Unübertroffene Ausstattungsmerkmale Audio-DACsWord Clock Synchronisation Lieferumfang Vor der ersten InbetriebnahmeHinweise zur Verwendung dieser Bedienungsanleitung Vor der ersten InbetriebnahmeAchtung Aufstellen des X-01 D2Allgemeines zu CD-R/CD-RWs Zur Wiedergabe mit dem X-01 D2 geeignete Disc-FormateAchtung WarnungAnfassen einer Disc Anschlüsse Analoge Audioausgänge Signal GND SignalmasseanschlussDigitale Audioausgänge LINK-Schnittstelle AudioEinsetzen von Batterien FernbedienungBatteriewechsel Vorsichtsmaßnahmen im Umgang mit BatterienDAC-Anzeige Bedienelemente auf der GerätevorderseiteFernbedienungssensor Display Disc-Schublade und VerschlussZifferntasten Verwenden der FernbedienungPlay Area Wiedergabebereich Cursor-Tasten und EnterDisplay Unterbrechen der Wiedergabe Pause WiedergabeBeenden der Wiedergabe Öffnen und Schließen der Disc-SchubladeVerwenden der SKIP-Tasten Auswählen eines MusiktitelsSchneller Suchlauf Löschen des letzten Titels einer Liste Wiedergabe einer programmierten TitelfolgeTitel zu einer Liste hinzufügen Löschen einer kompletten TitelfolgeEinstellen der Display-Helligkeit WiedergabewiederholungWiedergabewiederholung von Musiktiteln Wiedergabewiederholung aller TitelNormalanzeige Ändern der DisplayanzeigeDAC D/A-Wandler REF. ReferenzBit 1-Bit Layer bevorzugter Wiedergabebereich Einstellungen Einleitung Einstellungen Setup-Menü-Diagramm Einstellungen Audio Setup Analogausgang Analog OutDigitalausgang DigitalOut Large groß Abmessungen der Lautsprecherboxen SP SizeSmall klein On nur SubwooferDauer des Testtonsignals Test tone Abstand der Lautsprechersysteme zur Hörposition DistanceLautsprecher-Wiedergabepegel SP Level Datenübertragungsrate Kopierschutzsystem DtcpAnschließen mehrerer i.LINK-kompatibler Komponenten HinweiseTechnische Daten Hilfe bei Funktionsstörungen Pflege und Wartung Vermeiden Sie KondensationsbildungTeac Esoteric Company

X-01 D2 specifications

The Teac X-01 D2 is a premier audio component that has garnered attention among audiophiles and music enthusiasts. Designed with a keen focus on sound quality and advanced technology, it is celebrated for its exceptional playback capabilities and versatile features.

At its core, the Teac X-01 D2 is a high-end CD player that seamlessly combines modern digital advancements with classic analog design principles. It features a high-precision, slot-loading disc mechanism that not only enhances the convenience of use but also contributes to minimized vibrations during playback. This ensures that the audio signal remains clean and unaffected, resulting in superior sound quality.

One of the standout features of the X-01 D2 is its Dual-DAC architecture, utilizing two high-performance Digital-to-Analog Converters. This design allows for greater detail and dynamic range in audio playback, providing listeners with a rich and immersive experience. The unit supports various audio formats, including standard CDs, as well as high-resolution audio files, ensuring that users can enjoy their music in the utmost fidelity.

The incorporation of TEAC's proprietary technologies also elevates the performance of the X-01 D2. The Ultra-Linear Circuitry minimizes noise and distortion, while the high-quality, low-jitter clock circuitry ensures accurate signal processing. As a result, the audio produced is remarkably clear and precise, showcasing the nuances in even the most complex musical pieces.

Additionally, the Teac X-01 D2 includes multiple digital outputs, allowing users the flexibility to connect to a range of audio systems. These outputs include AES/EBU, coaxial, and optical connections, making it compatible with various audio equipment. The unit also features an analog output, providing connection options for those who prefer a classic analog connection to their amplifiers.

User-friendly controls and an intuitive interface further enhance the overall experience with the X-01 D2. Users can easily navigate through their music collection, adjusting settings and playback modes with ease. Its sleek design, complemented by a high-quality build, ensures that it fits seamlessly into any audio setup, both aesthetically and functionally.

In summary, the Teac X-01 D2 stands as a testament to the brand's commitment to quality and innovation. With its advanced technologies and features, it delivers an unparalleled listening experience that is sure to satisfy even the most discerning audio enthusiasts.
Top Page Image Contents