Fujitsu E600 user manual Iii

Page 3

13.Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power cord or plug is damaged or frayed.

b.If liquid has been spilled into the product.

c.If the product has been exposed to rain or water.

d.If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition.

e.If the product has been dropped or the cabinet has been damaged.

f.If the product exhibits a distinct change in performance, indicating a need for service.

14.CAUTION. When replacing the battery, be sure to install it with the polarities in the correct position. There is a danger of explosion if the battery is replaced with an incorrect type or is mistreated. Do not recharge, disassemble or dispose of in fire. Replace only with the same or equivalent type recommeded by the manufacturer. Dispose of the used battery according to the manufacturer’s instructions.

15.Use only the proper type of power supply cord set (provided in your accessories box) for this unit. It should be a detachable type: UL listed/CSA certified, BS1363,ASTA,SS145 certified, rated 10A 250V minimum, VDE approved or its equivalent. Maximum length is 15 feet (4.6 meters).

16.NOTE:

Please take extra precaution when connecting the LAN cable; do not connect the LAN cable to the peripheral device’s connector, that might have excessive voltage.

iii

Image 3
Contents Deskpower E600 Series User’s Manual Important Safety Instructions Iii For Safe Operation Before reading this manualBacking Up the Data Using this Product for High-Safety ApplicationsMicrosoft Service Pack Conventions Used in This Manual IntroductionNotational conventions Energy saving SafetyImportant Notes Manufacturer’s notesFCC Class B Compliance Statement Transporting the PC Cleaning the PCCleaning the system unit and the monitor Cleaning the keyboard and the mouseReference to products Disposal and recyclingXii Before Reading This Manual Organization of This ManualContents System Expansion Technical DataXvi Chapter External devices Steps for Initial SetupPreparing for Use Unpacking and Checking the DeliveryVertical operating position Setting Up the PCPage Connecting the monitor Connecting standard keyboardConnect the Monitor, Mouse and Keyboard Connecting USB mouse Connecting the mouseConnecting the keyboard Connecting a PS/2 mouseConnecting the PC to the Mains Voltage Switching on monitor and PC Initial Switch-on Software will be InstalledDisconnecting cables Connecting External DevicesInstalling the software Connecting cablesPorts on the PC LANSettings of the parallel port Connecting external devices to the serial portConnecting external devices to the parallel port Settings of the serial portConnecting external devices to the USB ports Operation Switching On the PC Switching Off the PCOperation SmartCard reader indicator Indicators On the PCCD-ROM indicator Floppy disk indicatorHard disk indicator Power-on indicatorLocking the casing Settings in Bios SetupProperty and Data Protection Unlocking and Locking CasingAnti-theft Protection and Lead-sealing Bios Setup Security FunctionsTroubleshooting Tips Internal power supply overloaded Troubleshooting and TipsInstalling New Software Mains voltage supply is faultyScreen stays blank Wrong RAM modules have been inserted No Mouse Pointer Displayed on the ScreenFloppy Disk Cannot be Read or Written Wrong monitor has been set under Window XPTips Error Messages on the ScreenRestoring the Hard Disk Contents Time and/or Date is not CorrectPage System Expansion Information about Boards System ExpansionOpening the Casing Closing the Casing Installing and Removing a Board Installing board bracketRemoving board bracket Make the required settings for the board Installing a boardPage Removing a board Page Low-Profile Boards Mounting slot adapterRemoving slot adapter Installing the graphics card Installing and Removing the Graphics CardRemoving the graphics card Installing and Removing Drives Replacing Drive in 51/2 inch BayIDE drives and serial ATA drives Close the casing see Closing the casing chapter Folding Up and Down the Drive Cage Changing the Floppy Disk Drive Replacing a Hard Disk Drive Page Page Replacing Lithium Battery Technical Data Electrical Data Technical Data