Fujitsu M3099GH, M3099EX, M3099EH manual Button SpecificationM3099GX/GH

Page 52

Button Specification(M3099GX/GH)

This section describes the button specifications.

Manual button

This button is used to select manual feed mode. Pressing this button switches the setting between Manual mode and ADF mode.

When this button is pressed, the scanner enters manual feed mode and the hopper goes up. If the button is pressed again, the scanner exits manual feed mode and the hopper goes down.

Start / Stop button

These buttons are usedd in Off-line mode. When Start button is pressed in Off-line mode, the scanner starts document feeding. When Stop button is pressed in Off-line mode, the scanner stops document feeding.

Stop button is also used in On-line mode to cancel the temporary error condition.

Mode 1 button

This button is used to transit to SETUP mode when the power is on. When Mode 1 button is pressed and power is turned on, the scanner enters SETUP mode.

Mode 2 button

This button is used to transit to maintenance mode when the power is on. When Mode 2 button is pressed and power switch is turned on, the scanner enters maintenance mode. Maintenance mode is used for maintenance/diagnostic purpose. See M3099EX/GX/EH/GH IMAGE SCANNER CE MANUAL.

3-17

Image 52

Contents M3099EX/GX/EH/GHImageScanner M3099EX/GX/EH/GH ImageScanner M3099EX/GX/EH/GHImageScanner OperatorsGuide Page Fujitsu Australia Limited Important Note to Users Preface CONNECTION, Operating INSTRUCTION,DOCUMENT SpecificaConventions Page Contents Page Specifications Endorser Setup Mode Glossary of Teams Index Components Cheking the Components Types Units and AssembliesUnits Assemblies Operator PanelM3099EX/EH ArrangementButton LED Function StartSimplex reading mode LCD DisplayDuplex reading mode Power-on Operation statusAbrasion counter Operator PanelM3099GX/GH Operator panelButton name Function Power-On to Ready A n n e r R e a d X X X X X Abrasion counter Error Function Buzzer FunctionsInstallationandconnections Precautions AchtungInspection Label C An example Connecting the power cable Turning the power switch offCable Connection Connecting the interface cable M3099EX/EHPage Operatinginstruction Turning the Power On Button Specification and Reading Mode Setting M3099EX/EH Z e D L T L T L G a 3 A4 Size buttonZ e L T L G a A u t o S 0Z e D L T L T L G a 3 a Z e L G a0 H T 1 L L f t o n e0 HT DOC . L N e H o t o Display ExplanationF a 0 H T Screen transition Z e D L T L T A 3 a A 4 S i z e L T0 2 0 A 4 S i z e D L T L G a DOC N e H o t o ButtonF a 0 H T 1 L 1 L A u t o 2 L DOC I n e H o t oFront/Back button pressed Stop button Button SpecificationM3099GX/GH Page Documentspecification Document Size M3099EH/GHPaper weight PrecautionsDocument Quality Document typePage Page Specifications Installation Specifications SpecificationDimensions Name Specification Remark ConsumablesOption Endorser Specifications How to set the endorser on or OFF Panel OperationHow to set the initial number How to select the print number reset method How to reset the print number manuallyHow to reset the print head life counter How to test the printing using the operator panelPage Setupmode Activating the Setup Mode Contents of the Setup Mode Setting double feed detection Setting IPC-2 pre-set mode Mode DetailsIf you press DTC Reset of abrasion counter Setting buzzerSetting pre-pick Adjusting LCD contrastSetting pick speed Setting initial value of endorserResetting of endorser Setting reset method of endorserResetting of ink counter Setting RS-232C transfer rate M3099EX/EH Setting SCSI-ID M3099GX/GHSetting Product-ID M3099GX/GH Setting picking start timeSetting picking time Setting time-out limitSetting hopper time Setting heater controlAutomatic start mode manual start mode A4 sizeAbrasion counter Automatic separationDuplex reading mode Equipment ErrorError diffusion Double feed detectionFront-side reading = Front-side scanning Halftone processingHeater control HexadecimalIPC-2 pre-set mode Linedrawing modeManual Feed mode = Manual Mode Manual start mode automatic start modePhotograph mode White level follower on Photo mode = photograph modeNoise removal Outline extractionPrint number reset method Reset method of endorserPre-picking Print headSetup mode Simplex reading modeStart command time-out Temporary ErrorGL-8 Index EX/EH Page IN-4 Page