Fujitsu M3099GX, M3099GH, M3099EX manual Document Quality, Document type, Paper weight, Precautions

Page 56

Document Quality

This section describes document types and weights available for the scanner, and precautions.

Document type

The recommended paper type for document is as follows:

NOTE

Use the specified paper only. (In rare occasion, double feeding may occur or document damage may occur.)

•Fine paper

•Plain paper (for example, the paper specified for XEROX4024)

•OCR paper

When using all other type paper, check that it is successfully fed by ADF before performing a reading operation.

Paper weight

The paper weight is as follows :

• 52 to 127 g/m2 3.9 to 34 lb)

Precautions

Be careful not to scan the following document. Preliminary document feed test may be necessary to avoid the unexpected errors. If the document slips in ADF (JAM error) or double feed occurs frequently, separation pressure adjustment in Reference Guide may be effective.

•Paper with clips

•Paper with wet ink

•Paper of which thickness is not constantly equal. (like envelope)

•Paper with large rumples or curl. (See NOTE on the next page.)

•Paper with folds or tears

•Tracing paper

•Coating paper

•Carbon paper

•Carbonless paper

•Paper smaller than 76 mm x 63 mm size, or larger than A3

•Other than paper ; clothes, metal foil, or OHP film

•Photographic paper

•Paper with notches on its side

•Other than rectangle paper

4-2

Page 55 Page 57
Image 56
Page 55 Page 57
Contents M3099EX/GX/EH/GHImageScanner M3099EX/GX/EH/GH ImageScanner M3099EX/GX/EH/GHImageScanner OperatorsGuide Page Fujitsu Australia Limited Important Note to Users Preface CONNECTION, Operating INSTRUCTION,DOCUMENT SpecificaConventions Page Contents Page Specifications Endorser Setup Mode Glossary of Teams Index Components Cheking the Components Units Units and AssembliesTypes Assemblies Operator PanelM3099EX/EH ArrangementButton LED Function StartSimplex reading mode LCD DisplayDuplex reading mode Power-on Operation statusAbrasion counter Operator PanelM3099GX/GH Operator panelButton name Function Power-On to Ready A n n e r R e a d X X X X X Abrasion counter Error Function Buzzer FunctionsInstallationandconnections Precautions AchtungInspection Label C An example Cable Connection Turning the power switch offConnecting the power cable Connecting the interface cable M3099EX/EHPage Operatinginstruction Turning the Power On Button Specification and Reading Mode Setting M3099EX/EH Z e L T L G a Size buttonZ e D L T L T L G a 3 A4 A u t o S 0Z e D L T L T L G a 3 a Z e L G a0 H T 1 L L f t o n e0 HT DOC . L N e H o t o Display ExplanationF a 0 H T Screen transition 0 2 0 A 4 S i z e L TZ e D L T L T A 3 a A 4 S i z e D L T L G a F a 0 H T 1 L ButtonDOC N e H o t o 1 L A u t o 2 L DOC I n e H o t oFront/Back button pressed Stop button Button SpecificationM3099GX/GH Page Documentspecification Document Size M3099EH/GHPaper weight PrecautionsDocument Quality Document typePage Page Specifications Installation Specifications SpecificationDimensions Name Specification Remark ConsumablesOption Endorser Specifications How to set the endorser on or OFF Panel OperationHow to set the initial number How to select the print number reset method How to reset the print number manuallyHow to reset the print head life counter How to test the printing using the operator panelPage Setupmode Activating the Setup Mode Contents of the Setup Mode Setting double feed detection Setting IPC-2 pre-set mode Mode DetailsIf you press DTC Reset of abrasion counter Setting buzzerSetting pre-pick Adjusting LCD contrastSetting pick speed Setting initial value of endorserResetting of ink counter Setting reset method of endorserResetting of endorser Setting RS-232C transfer rate M3099EX/EH Setting SCSI-ID M3099GX/GHSetting Product-ID M3099GX/GH Setting picking start timeSetting picking time Setting time-out limitSetting hopper time Setting heater controlAutomatic start mode manual start mode A4 sizeAbrasion counter Automatic separationDuplex reading mode Equipment ErrorError diffusion Double feed detectionFront-side reading = Front-side scanning Halftone processingHeater control HexadecimalIPC-2 pre-set mode Linedrawing modeManual Feed mode = Manual Mode Manual start mode automatic start modePhotograph mode White level follower on Photo mode = photograph modeNoise removal Outline extractionPrint number reset method Reset method of endorserPre-picking Print headSetup mode Simplex reading modeStart command time-out Temporary ErrorGL-8 Index EX/EH Page IN-4 Page
Top Page Image Contents