Fujitsu M3099GX manual Serial interface, Setup mode, SFI sensor, Simplex reading mode, Smoothing

Page 92

Serial interface

A standard computer interface. Information is transferred between devices over a single wire (although other wires are used for control).

With a serial interface, an interface cable greater than 3 meters (10 feet) can be used. This is often necessary in networking environments, where the scanner may be shared.

SETUP mode

In this mode, users can view or set a variety of function in Off-line.

SFI sensor

The document detection sensor. It detects the light that transmits the paper. It also detects the double feed error.

Simplex reading mode

Only the front side of the document is read in this mode. Place the documents face-up at the center of the hopper table.

Smoothing

Smoothing eliminates jaggies from slanted lines and curves. Irregular convexities are deleted and irregular concavities filled in. This is useful in OCR applications, for example.

Start command time-out

Occurs if START command does not arrive before the specified time after reading the previous document is complete. In this case the hopper table is lowered.

Temporary Error

An error that is recoverable by operator.

Terminator

Devices with SCSI interface are daisy-chained. A resistor that includes terminal circuits needs to be placed at both ends of a cable when devices are daisy-chained.

GL-7

Image 92

Contents M3099EX/GX/EH/GHImageScanner M3099EX/GX/EH/GH ImageScanner M3099EX/GX/EH/GHImageScanner OperatorsGuide Page Fujitsu Australia Limited Important Note to Users Preface CONNECTION, Operating INSTRUCTION,DOCUMENT SpecificaConventions Page Contents Page Specifications Endorser Setup Mode Glossary of Teams Index Components Cheking the Components Units Units and AssembliesTypes Assemblies Operator PanelM3099EX/EH ArrangementButton LED Function StartSimplex reading mode LCD DisplayDuplex reading mode Power-on Operation statusAbrasion counter Operator PanelM3099GX/GH Operator panelButton name Function Power-On to Ready A n n e r R e a d X X X X X Abrasion counter Error Function Buzzer FunctionsInstallationandconnections Precautions AchtungInspection Label C An example Cable Connection Turning the power switch offConnecting the power cable Connecting the interface cable M3099EX/EHPage Operatinginstruction Turning the Power On Button Specification and Reading Mode Setting M3099EX/EH Z e L T L G a Size buttonZ e D L T L T L G a 3 A4 A u t o S 0Z e D L T L T L G a 3 a Z e L G a0 H T 1 L L f t o n e0 HT DOC . L N e H o t o Display ExplanationF a 0 H T Screen transition 0 2 0 A 4 S i z e L TZ e D L T L T A 3 a A 4 S i z e D L T L G a F a 0 H T 1 L ButtonDOC N e H o t o 1 L A u t o 2 L DOC I n e H o t oFront/Back button pressed Stop button Button SpecificationM3099GX/GH Page Documentspecification Document Size M3099EH/GHPaper weight PrecautionsDocument Quality Document typePage Page Specifications Installation Specifications SpecificationDimensions Name Specification Remark ConsumablesOption Endorser Specifications How to set the endorser on or OFF Panel OperationHow to set the initial number How to select the print number reset method How to reset the print number manuallyHow to reset the print head life counter How to test the printing using the operator panelPage Setupmode Activating the Setup Mode Contents of the Setup Mode Setting double feed detection Setting IPC-2 pre-set mode Mode DetailsIf you press DTC Reset of abrasion counter Setting buzzerSetting pre-pick Adjusting LCD contrastSetting pick speed Setting initial value of endorserResetting of ink counter Setting reset method of endorserResetting of endorser Setting RS-232C transfer rate M3099EX/EH Setting SCSI-ID M3099GX/GHSetting Product-ID M3099GX/GH Setting picking start timeSetting picking time Setting time-out limitSetting hopper time Setting heater controlAutomatic start mode manual start mode A4 sizeAbrasion counter Automatic separationDuplex reading mode Equipment ErrorError diffusion Double feed detectionFront-side reading = Front-side scanning Halftone processingHeater control HexadecimalIPC-2 pre-set mode Linedrawing modeManual Feed mode = Manual Mode Manual start mode automatic start modePhotograph mode White level follower on Photo mode = photograph modeNoise removal Outline extractionPrint number reset method Reset method of endorserPre-picking Print headSetup mode Simplex reading modeStart command time-out Temporary ErrorGL-8 Index EX/EH Page IN-4 Page