Husky HME-421E, HME-423E user manual Wall Mounting, Wiring The Power Inputs

Page 12

Hardware Installations

3.Check if the DIN-Rail is tightened on the track or not.

4.To remove the switch from the track, reverse steps above.

2-5.1.2 Wall Mounting

Follow the steps below for wall-mounting installation.

1.Remove the DIN-Rail plate from the switch; loosen the screws to remove the DIN-Rail plate.

2.Place the wall mounting plate on the back panel of the switch.

3.Use the screws to screw the wall mounting plates on the switch.

4.Use the hook holes at the corners of the wall mounting plates to place the switch on the wall.

5.To remove the wall mounting plate, reverse the steps above.

2-5.2 Wiring The Power Inputs

Follow the steps below to wire the power inputs.

Be sure to disconnect the power cord before installing and/or wiring your switch.

Be sure of the maximum possible current when wiring connections. If the current goes above the maximum ratings, the wire could overheat and result in serious damage to your switch.

1.Insert the positive and negative wires of your DC supply into the corresponding V+ and V- contacts of the terminal block.

2. Tighten the screws to prevent the DC wires from coming detached.

2-5

Image 12

Contents HME-421E/423E Copyright Notice Table of Contents Ring Application Couple Ring Dual Homing Dual Ring Page Product Features IntroductionOverview Package Checklist Hardware Installation Dimensions and Panel LayoutFront Panel Side Panel Back Panel Bottom PanelLED Indicators RJ-45 PortsLED Name LED Color LED Function 1 RJ-45 Pin AssignmentsFiber Ports PinInstalling Your Ethernet Direct Switch Mounting The SwitchDIN-Rail Mounting Wiring The Power Inputs Wall MountingWiring The Fault Alarm Contact CablingPage Configuration Using Console Interface Connecting Console PortLogin The Console Interface CLI ManagementCommand Levels Modes Access Method Prompt Exit Method About This ModeConfigure DatabaseConfiguration Using a Web Browser System LoginAbout Web-based Management Interface Preparing for Web-based ManagementBasic Settings Management Main ScreenUser Authentication Confirm passwordPort Statistics PortFault Relay Alarm Power FailureIP Configuration Port Link Down/BrokenRestoring Configurations by Tftp Backing up Configurations by TftpUpdating Firmware by Tftp Advanced Management Settings Speed DuplexSecurity Rate LimitingPort Mirroring Destination PortSource Port Dhcp ServerLow IP Address High IP AddressLease Time sec Port and IP Bindings by Dhcp ServerSystem Event Log Syslog Configuration Syslog Client ModeSystem Log Server IP AddressSmtp Configuration AuthenticationEmail Alert Smtp Server IPEvent Configuration System event selectionPort event selection Sntp Configuration Sntp ClientDaylight Saving Time UTC TimezoneMins Switch Timer IP Security ModeEnable Http Server Enable Telnet ServerAggregator Settings Port TrunkingSystem Priority Group IDLacp Disabled Aggregator InformationGroup Key Port MemberLacp Enabled State Activity Vlan Configuration Port-based VlanPage 11.2.1 802.1Q Configuration Vlan Operation Mode Enable GvrpIeee 802.1Q Tag-based Vlan Management Vlan IDLink Type Untagged VIDTagged VID Group Configuration QoS Configuration Use an 8, 4, 2, 1 weighted fair queuing schemeQoS Policy Use the strict priority schemeIgmp Configuration Snmp Configuration Agent ModeLeave Group Community StringsTrap Configuration Snmp v3 ConfigurationCommunity Trap VersionContext Table Context Name Group Table Security Name User IDAccess Table Context Prefix Security LevelContext Match Rule Read View NameLldp Configuration Lldp ProtocolLldp Interval Rapid Spanning Tree Protocol Configuration Rstp System ConfigurationRstp Mode Forward Delay TimeAdmin P2P Admin EdgeAdmin Non Stp Ring ConfigurationEnable Ring Enable Couple RingEnable Dual Homing Enable Dual Ring18 802.1X/Radius Configuration Ieee 802.1x ProtocolRadius Server IP Server PortDisable Misc ConfigurationReject AcceptSupplicant Timeout Server TimeoutStatic MAC Address Settings Max RequestsMAC Filtering All MAC AddressesMulticast Filtering Member PortsNetwork Applications Ring ApplicationCouple Ring Dual Homing Example of Couple Ring ConnectionNetwork Applications Example of Dual Ring Connection Diagram Dual RingSpecifications TechnologyRegulatory Approvals Management Specifications Dhcp Troubleshooting Appendix BCommand Set Lists Commands Set ListSystem Commands Set Port Commands Set Broadcast-multicast-flooded-unicast Broadcast-multicastBroadcast-only Trunk Commands Set Vlan Commands SetSwitch#vlan database Switchvlan#vlanmode portbaseSwitchvlan#vlanmode 802.1q Ported based Vlan configurationSpanning Tree Commands Set QoS Commands Set Igmp Commands SetMac / Filter Table Commands Set Snmp Commands SetSwitchconfig#snmpv3 context-name Switchconfig#snmpv3 user test01Group G1 password AuthPW PrivPW Switchconfig#snmpv3 mibview viewPort Mirroring Commands Set 12 802.1x Commands SetTftp Commands Set SystemLog, Smtp and Event Commands Set Sntp Commands Set Ring Commands SetSwitchconfig#ring homingport Switch#show ringSwitchconfig# no ring couplering Switchconfig# no ring dualhoming