Husky HME-423E, HME-421E user manual Igmp Configuration

Page 41

Configuration Using a Web Browser

set the TOS level 25 to be high. The port 1 is following the TOS priority policy only. When the packet received by port 1, the switch will check the TOS value of the received IP packet. If the TOS value of received IP packet is 25 (priority = high), and then the packet priority will have the highest priority.

QoS and Rate Limiting function cannot be enabled at the same time.

After finishing necessary configurations, click on Apply to save the settings.

4-6.13 IGMP Configuration

The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP). IGMP Snooping mode allows the switch to forward multicast packets to appropriate ports. The switch will detect IGMP queries when multicast packets come in and then report back with packets indicating which port is willing to accept the multicast packets. With this function, network traffic can be limited without unwanted packets being sent to certain ports. IGMP has three fundamental types of messages as follows:

	Message	Description
	Query	A message sent from the querier (IGMP router or switch) asking for a
	Query	response from each host belonging to the multicast group.
		response from each host belonging to the multicast group.
	Report	A message sent by a host to the querier to indicate that the host wants to
	Report	be or is a member of a given group indicated in the report message.

4-25

Image 41

Contents HME-421E/423E Copyright Notice Table of Contents Ring Application Couple Ring Dual Homing Dual Ring Page Overview Product FeaturesIntroduction Package Checklist Dimensions and Panel Layout Hardware InstallationFront Panel Side Panel Back Panel Bottom PanelRJ-45 Ports LED IndicatorsLED Name LED Color LED Function 1 RJ-45 Pin AssignmentsPin Fiber PortsDIN-Rail Mounting Installing Your Ethernet Direct SwitchMounting The Switch Wall Mounting Wiring The Power InputsCabling Wiring The Fault Alarm ContactPage Connecting Console Port Configuration Using Console InterfaceLogin The Console Interface CLI ManagementModes Access Method Prompt Exit Method About This Mode Command LevelsConfigure DatabaseSystem Login Configuration Using a Web BrowserAbout Web-based Management Interface Preparing for Web-based ManagementManagement Main Screen Basic SettingsConfirm password User AuthenticationPort Statistics PortPower Failure Fault Relay AlarmIP Configuration Port Link Down/BrokenUpdating Firmware by Tftp Restoring Configurations by TftpBacking up Configurations by Tftp Advanced Management Settings Duplex SpeedSecurity Rate LimitingDestination Port Port MirroringSource Port Dhcp ServerHigh IP Address Low IP AddressLease Time sec Port and IP Bindings by Dhcp ServerSyslog Client Mode System Event Log Syslog ConfigurationSystem Log Server IP AddressAuthentication Smtp ConfigurationEmail Alert Smtp Server IPPort event selection Event ConfigurationSystem event selection Sntp Client Sntp ConfigurationDaylight Saving Time UTC TimezoneIP Security Mode Mins Switch TimerEnable Http Server Enable Telnet ServerPort Trunking Aggregator SettingsSystem Priority Group IDAggregator Information Lacp DisabledGroup Key Port MemberLacp Enabled State Activity Port-based Vlan Vlan ConfigurationPage Enable Gvrp 11.2.1 802.1Q Configuration Vlan Operation ModeIeee 802.1Q Tag-based Vlan Management Vlan IDTagged VID Link TypeUntagged VID Group Configuration Use an 8, 4, 2, 1 weighted fair queuing scheme QoS ConfigurationQoS Policy Use the strict priority schemeIgmp Configuration Agent Mode Snmp ConfigurationLeave Group Community StringsSnmp v3 Configuration Trap ConfigurationCommunity Trap VersionGroup Table Security Name User ID Context Table Context NameSecurity Level Access Table Context PrefixContext Match Rule Read View NameLldp Interval Lldp ConfigurationLldp Protocol System Configuration Rapid Spanning Tree Protocol Configuration RstpRstp Mode Forward Delay TimeAdmin Edge Admin P2PAdmin Non Stp Ring ConfigurationEnable Couple Ring Enable RingEnable Dual Homing Enable Dual RingIeee 802.1x Protocol 18 802.1X/Radius ConfigurationRadius Server IP Server PortMisc Configuration DisableReject AcceptServer Timeout Supplicant TimeoutStatic MAC Address Settings Max RequestsAll MAC Addresses MAC FilteringMember Ports Multicast FilteringCouple Ring Network ApplicationsRing Application Example of Couple Ring Connection Dual HomingNetwork Applications Dual Ring Example of Dual Ring Connection DiagramRegulatory Approvals SpecificationsTechnology Management Specifications Dhcp Appendix B TroubleshootingSystem Commands Set Command Set ListsCommands Set List Port Commands Set Broadcast-only Broadcast-multicast-flooded-unicastBroadcast-multicast Vlan Commands Set Trunk Commands SetSwitchvlan#vlanmode portbase Switch#vlan databaseSwitchvlan#vlanmode 802.1q Ported based Vlan configurationSpanning Tree Commands Set Igmp Commands Set QoS Commands SetSnmp Commands Set Mac / Filter Table Commands SetSwitchconfig#snmpv3 user test01 Switchconfig#snmpv3 context-nameGroup G1 password AuthPW PrivPW Switchconfig#snmpv3 mibview view12 802.1x Commands Set Port Mirroring Commands SetTftp Commands Set SystemLog, Smtp and Event Commands Set Ring Commands Set Sntp Commands SetSwitch#show ring Switchconfig#ring homingportSwitchconfig# no ring couplering Switchconfig# no ring dualhoming