Husky HME-421E, HME-423E user manual Port Mirroring Commands Set, 12 802.1x Commands Set

Page 72

				Command Set Lists

	View Name] [Notify View
	Name]
	no snmpv3 mibview view	G	Remove specified	switch(config)#no snmpv3 mibview
	[View Name]		mibview table of SNMPV3	view V1 type Excluded sub-oid 1.3.6.1
	type		agent.
	[ExcludedIncluded]
	sub-oid
	[OID]

C-11 Port Mirroring Commands Set

Commands	Level	Description	Example
monitor	I	Configure source port of	switch(config)#interface fastEthernet 2
[RXTXBoth]		monitor function	switch(config-if)#monitor RX
monitor rx [Port ID]	G	Set RX destination port of	switch(config)#monitor rx 2
		monitor function
monitor tx [Port ID]	G	Set TX destination port of	switch(config)#monitor tx 3
		monitor function
show monitor	P	Show port monitor	switch#show monitor
		information
show monitor	I	Show port monitor	switch(config)#interface fastEthernet 2
		information	switch(config-if)#show monitor
no monitor	I	Disable source port of	switch(config)#interface fastEthernet 2
		monitor function	switch(config-if)#no monitor

C-12 802.1x Commands Set

Commands	Level	Description	Example
8021x enable	G	Use the 802.1x global	switch(config)# 8021x enable
		configuration command to
		enable 802.1x protocols.
8021x system radiusip	G	Use the 802.1x system	switch(config)# 8021x system radiusip
[IP address]		radius IP global	192.168.1.1
		configuration command to
		change the radius server
		IP.
8021x system serverport	G	Use the 802.1x system	switch(config)# 8021x system
[port ID]		server port global	serverport 1812
		configuration command to
		change the radius server
		port.
8021x system accountport	G	Use the 802.1x system	switch(config)# 8021x system
[port ID]		account port global	accountport 1813
		configuration command to
		change the accounting
		port.
8021x system sharedkey	G	Use the 802.1x system	switch(config)# 8021x system
[ID]		share key global	sharedkey 123456
		configuration command to
		change the shared key
		value.
8021x system nasid	G	Use the 802.1x system	switch(config)# 8021x system nasid
[words]		nasid global configuration	test1

C-10

Image 72

Contents HME-421E/423E Copyright Notice Table of Contents Ring Application Couple Ring Dual Homing Dual Ring Page Product Features IntroductionOverview Package Checklist Hardware Installation Dimensions and Panel LayoutFront Panel Side Panel Back Panel Bottom PanelLED Indicators RJ-45 PortsLED Name LED Color LED Function 1 RJ-45 Pin AssignmentsFiber Ports PinInstalling Your Ethernet Direct Switch Mounting The SwitchDIN-Rail Mounting Wiring The Power Inputs Wall MountingWiring The Fault Alarm Contact CablingPage Configuration Using Console Interface Connecting Console PortLogin The Console Interface CLI ManagementCommand Levels Modes Access Method Prompt Exit Method About This ModeConfigure DatabaseConfiguration Using a Web Browser System LoginAbout Web-based Management Interface Preparing for Web-based ManagementBasic Settings Management Main ScreenUser Authentication Confirm passwordPort Statistics PortFault Relay Alarm Power FailureIP Configuration Port Link Down/BrokenRestoring Configurations by Tftp Backing up Configurations by TftpUpdating Firmware by Tftp Advanced Management Settings Speed DuplexSecurity Rate LimitingPort Mirroring Destination PortSource Port Dhcp ServerLow IP Address High IP AddressLease Time sec Port and IP Bindings by Dhcp ServerSystem Event Log Syslog Configuration Syslog Client ModeSystem Log Server IP AddressSmtp Configuration AuthenticationEmail Alert Smtp Server IPEvent Configuration System event selectionPort event selection Sntp Configuration Sntp ClientDaylight Saving Time UTC TimezoneMins Switch Timer IP Security ModeEnable Http Server Enable Telnet ServerAggregator Settings Port TrunkingSystem Priority Group IDLacp Disabled Aggregator InformationGroup Key Port MemberLacp Enabled State Activity Vlan Configuration Port-based VlanPage 11.2.1 802.1Q Configuration Vlan Operation Mode Enable GvrpIeee 802.1Q Tag-based Vlan Management Vlan IDLink Type Untagged VIDTagged VID Group Configuration QoS Configuration Use an 8, 4, 2, 1 weighted fair queuing schemeQoS Policy Use the strict priority schemeIgmp Configuration Snmp Configuration Agent ModeLeave Group Community StringsTrap Configuration Snmp v3 ConfigurationCommunity Trap VersionContext Table Context Name Group Table Security Name User IDAccess Table Context Prefix Security LevelContext Match Rule Read View NameLldp Configuration Lldp ProtocolLldp Interval Rapid Spanning Tree Protocol Configuration Rstp System ConfigurationRstp Mode Forward Delay TimeAdmin P2P Admin EdgeAdmin Non Stp Ring ConfigurationEnable Ring Enable Couple RingEnable Dual Homing Enable Dual Ring18 802.1X/Radius Configuration Ieee 802.1x ProtocolRadius Server IP Server PortDisable Misc ConfigurationReject AcceptSupplicant Timeout Server TimeoutStatic MAC Address Settings Max RequestsMAC Filtering All MAC AddressesMulticast Filtering Member PortsNetwork Applications Ring ApplicationCouple Ring Dual Homing Example of Couple Ring ConnectionNetwork Applications Example of Dual Ring Connection Diagram Dual RingSpecifications TechnologyRegulatory Approvals Management Specifications Dhcp Troubleshooting Appendix BCommand Set Lists Commands Set ListSystem Commands Set Port Commands Set Broadcast-multicast-flooded-unicast Broadcast-multicastBroadcast-only Trunk Commands Set Vlan Commands SetSwitch#vlan database Switchvlan#vlanmode portbaseSwitchvlan#vlanmode 802.1q Ported based Vlan configurationSpanning Tree Commands Set QoS Commands Set Igmp Commands SetMac / Filter Table Commands Set Snmp Commands SetSwitchconfig#snmpv3 context-name Switchconfig#snmpv3 user test01Group G1 password AuthPW PrivPW Switchconfig#snmpv3 mibview viewPort Mirroring Commands Set 12 802.1x Commands SetTftp Commands Set SystemLog, Smtp and Event Commands Set Sntp Commands Set Ring Commands SetSwitchconfig#ring homingport Switch#show ringSwitchconfig# no ring couplering Switchconfig# no ring dualhoming