Husky HME-423E, HME-421E user manual Updating Firmware by Tftp, Restoring Configurations by Tftp

Page 21

Configuration Using a Web Browser

After finishing necessary configurations, click on Apply to save the settings.

4-5.6 Updating Firmware by TFTP

This feature allows the administrator to update the switch firmware. Before updating, make sure the TFTP server is ready and the firmware image is on the TFTP server.

TFTP Server IP Address Use this feature to fill in your TFTP server IP.

Firmware File Name Use this feature to fill in the name of the firmware image.

After finishing necessary configurations, click on Apply to save the settings.

4-5.7 Restoring Configurations by TFTP

You can restore EEPROM value from the TFTP server. Before doing so, make sure the image file is already placed on TFTP server. The HME-421E/423E will download the flash image.

TFTP Server IP Address Use this feature to fill in your TFTP server IP.

Firmware File Name Use this feature to fill in the correct file name to be restored.

After finishing necessary configurations, click on Apply to save the settings.

4-5.8 Backing up Configurations by TFTP

With this feature, the administrator can save the current configurations from the HME-421E/423E to the TFTP server, and then go to the TFTP restoration configuration page to restore the settings.

TFTP Server IP Address Use this feature to fill in your TFTP server IP.

Firmware File Name Use this feature to fill in the file name.

4-5

Image 21

Contents HME-421E/423E Copyright Notice Table of Contents Ring Application Couple Ring Dual Homing Dual Ring Page Product Features IntroductionOverview Package Checklist Dimensions and Panel Layout Hardware InstallationFront Panel Side Panel Back Panel Bottom PanelRJ-45 Ports LED IndicatorsLED Name LED Color LED Function 1 RJ-45 Pin AssignmentsPin Fiber PortsInstalling Your Ethernet Direct Switch Mounting The SwitchDIN-Rail Mounting Wall Mounting Wiring The Power InputsCabling Wiring The Fault Alarm ContactPage Connecting Console Port Configuration Using Console InterfaceLogin The Console Interface CLI ManagementModes Access Method Prompt Exit Method About This Mode Command LevelsConfigure DatabaseSystem Login Configuration Using a Web BrowserAbout Web-based Management Interface Preparing for Web-based ManagementManagement Main Screen Basic SettingsConfirm password User AuthenticationPort Statistics PortPower Failure Fault Relay AlarmIP Configuration Port Link Down/BrokenRestoring Configurations by Tftp Backing up Configurations by TftpUpdating Firmware by Tftp Advanced Management Settings Duplex SpeedSecurity Rate LimitingDestination Port Port MirroringSource Port Dhcp ServerHigh IP Address Low IP AddressLease Time sec Port and IP Bindings by Dhcp ServerSyslog Client Mode System Event Log Syslog ConfigurationSystem Log Server IP AddressAuthentication Smtp ConfigurationEmail Alert Smtp Server IPEvent Configuration System event selectionPort event selection Sntp Client Sntp ConfigurationDaylight Saving Time UTC TimezoneIP Security Mode Mins Switch TimerEnable Http Server Enable Telnet ServerPort Trunking Aggregator SettingsSystem Priority Group IDAggregator Information Lacp DisabledGroup Key Port MemberLacp Enabled State Activity Port-based Vlan Vlan ConfigurationPage Enable Gvrp 11.2.1 802.1Q Configuration Vlan Operation ModeIeee 802.1Q Tag-based Vlan Management Vlan IDLink Type Untagged VIDTagged VID Group Configuration Use an 8, 4, 2, 1 weighted fair queuing scheme QoS ConfigurationQoS Policy Use the strict priority schemeIgmp Configuration Agent Mode Snmp ConfigurationLeave Group Community StringsSnmp v3 Configuration Trap ConfigurationCommunity Trap VersionGroup Table Security Name User ID Context Table Context NameSecurity Level Access Table Context PrefixContext Match Rule Read View NameLldp Configuration Lldp ProtocolLldp Interval System Configuration Rapid Spanning Tree Protocol Configuration RstpRstp Mode Forward Delay TimeAdmin Edge Admin P2PAdmin Non Stp Ring ConfigurationEnable Couple Ring Enable RingEnable Dual Homing Enable Dual RingIeee 802.1x Protocol 18 802.1X/Radius ConfigurationRadius Server IP Server PortMisc Configuration DisableReject AcceptServer Timeout Supplicant TimeoutStatic MAC Address Settings Max RequestsAll MAC Addresses MAC FilteringMember Ports Multicast FilteringNetwork Applications Ring ApplicationCouple Ring Example of Couple Ring Connection Dual HomingNetwork Applications Dual Ring Example of Dual Ring Connection DiagramSpecifications TechnologyRegulatory Approvals Management Specifications Dhcp Appendix B TroubleshootingCommand Set Lists Commands Set ListSystem Commands Set Port Commands Set Broadcast-multicast-flooded-unicast Broadcast-multicastBroadcast-only Vlan Commands Set Trunk Commands SetSwitchvlan#vlanmode portbase Switch#vlan databaseSwitchvlan#vlanmode 802.1q Ported based Vlan configurationSpanning Tree Commands Set Igmp Commands Set QoS Commands SetSnmp Commands Set Mac / Filter Table Commands SetSwitchconfig#snmpv3 user test01 Switchconfig#snmpv3 context-nameGroup G1 password AuthPW PrivPW Switchconfig#snmpv3 mibview view12 802.1x Commands Set Port Mirroring Commands SetTftp Commands Set SystemLog, Smtp and Event Commands Set Ring Commands Set Sntp Commands SetSwitch#show ring Switchconfig#ring homingportSwitchconfig# no ring couplering Switchconfig# no ring dualhoming