Husky HME-423E, HME-421E Configuration Using a Web Browser, About Web-based Management Interface

Page 17

Chapter 4

Configuration Using a Web Browser

This chapter contains information on how to configure your HME-421E/423E via a web browser. The topics include:

zAbout Web-based Management Interface

zPreparing for Web-based Management

zSystem Login

zManagement Main Screen

zBasic Settings

zAdvanced Management Settings

4-1 About Web-based Management Interface

HME-421E/423E offers an easy-to-use management interface, which allows users to manage the HME-421E/423E via a standard web browser such as IE from anywhere on the network.

This web-based management interface supports Internet Explorer 6.0 or later version. Java Applets is also applied for reducing network bandwidth consumption, enhancing access speed and presenting an easy-viewing screen.

4-2 Preparing for Web-based Management

Before using web-based management interface, install the HME-421E/423E onto the network and make sure that any one of PC on the network can access the HME-421E/423E through a web browser. The default settings of IP address, subnet mask, username, and password of the HME-421E/423E are as follows:

IP Address	192.168.16.1
Subnet Mask	255.255.255.0
Default Gateway	192.168.16.254
User Name	root
Password	root

4-3 System Login

Follow the steps below to login into the web-based management interface.

1.Launch the web browser.

2.Key in the default IP address in the web address box and press Enter.

3.The login window will appear.

4.Key in the user name and the password. The default username and password is root.

5.Press Enter or click OK, the main screen of web-based management interface will then appear. Please refer to the Management Main Screen section for more information.

4-1

Image 17

Contents HME-421E/423E Copyright Notice Table of Contents Ring Application Couple Ring Dual Homing Dual Ring Page Overview Product FeaturesIntroduction Package Checklist Dimensions and Panel Layout Hardware InstallationFront Panel Side Panel Back Panel Bottom PanelRJ-45 Ports LED IndicatorsLED Name LED Color LED Function 1 RJ-45 Pin AssignmentsPin Fiber PortsDIN-Rail Mounting Installing Your Ethernet Direct SwitchMounting The Switch Wall Mounting Wiring The Power InputsCabling Wiring The Fault Alarm ContactPage Connecting Console Port Configuration Using Console InterfaceLogin The Console Interface CLI ManagementModes Access Method Prompt Exit Method About This Mode Command LevelsConfigure DatabaseSystem Login Configuration Using a Web BrowserAbout Web-based Management Interface Preparing for Web-based ManagementManagement Main Screen Basic SettingsConfirm password User AuthenticationPort Statistics PortPower Failure Fault Relay AlarmIP Configuration Port Link Down/BrokenUpdating Firmware by Tftp Restoring Configurations by TftpBacking up Configurations by Tftp Advanced Management Settings Duplex SpeedSecurity Rate LimitingDestination Port Port MirroringSource Port Dhcp ServerHigh IP Address Low IP AddressLease Time sec Port and IP Bindings by Dhcp ServerSyslog Client Mode System Event Log Syslog ConfigurationSystem Log Server IP AddressAuthentication Smtp ConfigurationEmail Alert Smtp Server IPPort event selection Event ConfigurationSystem event selection Sntp Client Sntp ConfigurationDaylight Saving Time UTC TimezoneIP Security Mode Mins Switch TimerEnable Http Server Enable Telnet ServerPort Trunking Aggregator SettingsSystem Priority Group IDAggregator Information Lacp DisabledGroup Key Port MemberLacp Enabled State Activity Port-based Vlan Vlan ConfigurationPage Enable Gvrp 11.2.1 802.1Q Configuration Vlan Operation ModeIeee 802.1Q Tag-based Vlan Management Vlan IDTagged VID Link TypeUntagged VID Group Configuration Use an 8, 4, 2, 1 weighted fair queuing scheme QoS ConfigurationQoS Policy Use the strict priority schemeIgmp Configuration Agent Mode Snmp ConfigurationLeave Group Community StringsSnmp v3 Configuration Trap ConfigurationCommunity Trap VersionGroup Table Security Name User ID Context Table Context NameSecurity Level Access Table Context PrefixContext Match Rule Read View NameLldp Interval Lldp ConfigurationLldp Protocol System Configuration Rapid Spanning Tree Protocol Configuration RstpRstp Mode Forward Delay TimeAdmin Edge Admin P2PAdmin Non Stp Ring ConfigurationEnable Couple Ring Enable RingEnable Dual Homing Enable Dual RingIeee 802.1x Protocol 18 802.1X/Radius ConfigurationRadius Server IP Server PortMisc Configuration DisableReject AcceptServer Timeout Supplicant TimeoutStatic MAC Address Settings Max RequestsAll MAC Addresses MAC FilteringMember Ports Multicast FilteringCouple Ring Network ApplicationsRing Application Example of Couple Ring Connection Dual HomingNetwork Applications Dual Ring Example of Dual Ring Connection DiagramRegulatory Approvals SpecificationsTechnology Management Specifications Dhcp Appendix B TroubleshootingSystem Commands Set Command Set ListsCommands Set List Port Commands Set Broadcast-only Broadcast-multicast-flooded-unicastBroadcast-multicast Vlan Commands Set Trunk Commands SetSwitchvlan#vlanmode portbase Switch#vlan databaseSwitchvlan#vlanmode 802.1q Ported based Vlan configurationSpanning Tree Commands Set Igmp Commands Set QoS Commands SetSnmp Commands Set Mac / Filter Table Commands SetSwitchconfig#snmpv3 user test01 Switchconfig#snmpv3 context-nameGroup G1 password AuthPW PrivPW Switchconfig#snmpv3 mibview view12 802.1x Commands Set Port Mirroring Commands SetTftp Commands Set SystemLog, Smtp and Event Commands Set Ring Commands Set Sntp Commands SetSwitch#show ring Switchconfig#ring homingportSwitchconfig# no ring couplering Switchconfig# no ring dualhoming