Husky HME-421E, HME-423E user manual Trunk Commands Set, Vlan Commands Set

Page 66

				Command Set Lists

	show interface configuration	I	Show interface	switch(config)#interface fastEthernet 2
			configuration status	switch(config-if)#show interface
				configuration
	show interface status	I	Show interface actual	switch(config)#interface fastEthernet 2
			status	switch(config-if)#show interface status
	show interface accounting	I	Show interface statistic	switch(config)#interface fastEthernet 2
			counter	switch(config-if)#show interface
				accounting
	no accounting	I	Clear interface	switch(config)#interface fastEthernet 2
			accounting information	switch(config-if)#no accounting

C-4 Trunk Commands Set

Commands	Level	Description	Example
aggregator priority	G	Set port group system	switch(config)#aggregator priority 22
[1~65535]		priority
aggregator activityport	G	Set activity port	switch(config)#aggregator activityport
[Group ID]			2
[Port Numbers]
aggregator group	G	Assign a trunk group with	switch(config)#aggregator group 1 1-4
[GroupID] [Port-list]		LACP active.	lacp workp 2 or
lacp		[GroupID]: 1~3	switch(config)#aggregator group 2
workp		[Port-list]: Member port	1,4,3 lacp workp 3
[Workport]		list. This parameter could
		be a port range (ex.1-4) or
		a port list separate by a
		comma (ex.2, 3, 6)
		[Workport]: The amount of
		work ports. This value
		could not be less than
		zero or be large than the
		amount of member ports.
aggregator group	G	Assign a static trunk	switch(config)#aggregator group 1 2-4
[GroupID] [Port-list]		group.	nolacp or
nolacp		[GroupID]:1~3	switch(config)#aggregator group 1
		[Port-list]: Member port	3,1,2 nolacp
		list. This parameter could
		be a port range (ex.1-4) or
		a port list separate by a
		comma ex.2, 3, 6)
show aggregator	P	Show the information of	switch#show aggregator 1 or
		trunk group	switch#show aggregator 2 or
			switch#show aggregator 3

no aggregator lacp	G	Disable the LACP	switch(config)#no aggreator lacp 1
[GroupID]		function of trunk group

no aggregator group	G	Remove a trunk group	switch(config)#no aggreator group 2
[GroupID]

C-5 VLAN Commands Set

Commands

Level

Description

Example

C-4

Image 66

Contents HME-421E/423E Copyright Notice Table of Contents Ring Application Couple Ring Dual Homing Dual Ring Page Product Features IntroductionOverview Package Checklist Front Panel Side Panel Hardware InstallationDimensions and Panel Layout Back Panel Bottom PanelLED Name LED Color LED Function LED IndicatorsRJ-45 Ports 1 RJ-45 Pin AssignmentsFiber Ports PinInstalling Your Ethernet Direct Switch Mounting The SwitchDIN-Rail Mounting Wiring The Power Inputs Wall MountingWiring The Fault Alarm Contact CablingPage Login The Console Interface Configuration Using Console InterfaceConnecting Console Port CLI ManagementConfigure Command LevelsModes Access Method Prompt Exit Method About This Mode DatabaseAbout Web-based Management Interface Configuration Using a Web BrowserSystem Login Preparing for Web-based ManagementBasic Settings Management Main ScreenPort Statistics User AuthenticationConfirm password PortIP Configuration Fault Relay AlarmPower Failure Port Link Down/BrokenRestoring Configurations by Tftp Backing up Configurations by TftpUpdating Firmware by Tftp Advanced Management Settings Security SpeedDuplex Rate LimitingSource Port Port MirroringDestination Port Dhcp ServerLease Time sec Low IP AddressHigh IP Address Port and IP Bindings by Dhcp ServerSystem Log Server IP System Event Log Syslog ConfigurationSyslog Client Mode AddressEmail Alert Smtp ConfigurationAuthentication Smtp Server IPEvent Configuration System event selectionPort event selection Daylight Saving Time Sntp ConfigurationSntp Client UTC TimezoneEnable Http Server Mins Switch TimerIP Security Mode Enable Telnet ServerSystem Priority Aggregator SettingsPort Trunking Group IDGroup Key Lacp DisabledAggregator Information Port MemberLacp Enabled State Activity Vlan Configuration Port-based VlanPage Ieee 802.1Q Tag-based Vlan 11.2.1 802.1Q Configuration Vlan Operation ModeEnable Gvrp Management Vlan IDLink Type Untagged VIDTagged VID Group Configuration QoS Policy QoS ConfigurationUse an 8, 4, 2, 1 weighted fair queuing scheme Use the strict priority schemeIgmp Configuration Leave Group Snmp ConfigurationAgent Mode Community StringsCommunity Trap ConfigurationSnmp v3 Configuration Trap VersionContext Table Context Name Group Table Security Name User IDContext Match Rule Access Table Context PrefixSecurity Level Read View NameLldp Configuration Lldp ProtocolLldp Interval Rstp Mode Rapid Spanning Tree Protocol Configuration RstpSystem Configuration Forward Delay TimeAdmin Non Stp Admin P2PAdmin Edge Ring ConfigurationEnable Dual Homing Enable RingEnable Couple Ring Enable Dual RingRadius Server IP 18 802.1X/Radius ConfigurationIeee 802.1x Protocol Server PortReject DisableMisc Configuration AcceptStatic MAC Address Settings Supplicant TimeoutServer Timeout Max RequestsMAC Filtering All MAC AddressesMulticast Filtering Member PortsNetwork Applications Ring ApplicationCouple Ring Dual Homing Example of Couple Ring ConnectionNetwork Applications Example of Dual Ring Connection Diagram Dual RingSpecifications TechnologyRegulatory Approvals Management Specifications Dhcp Troubleshooting Appendix BCommand Set Lists Commands Set ListSystem Commands Set Port Commands Set Broadcast-multicast-flooded-unicast Broadcast-multicastBroadcast-only Trunk Commands Set Vlan Commands SetSwitchvlan#vlanmode 802.1q Switch#vlan databaseSwitchvlan#vlanmode portbase Ported based Vlan configurationSpanning Tree Commands Set QoS Commands Set Igmp Commands SetMac / Filter Table Commands Set Snmp Commands SetGroup G1 password AuthPW PrivPW Switchconfig#snmpv3 context-nameSwitchconfig#snmpv3 user test01 Switchconfig#snmpv3 mibview viewPort Mirroring Commands Set 12 802.1x Commands SetTftp Commands Set SystemLog, Smtp and Event Commands Set Sntp Commands Set Ring Commands SetSwitchconfig# no ring couplering Switchconfig#ring homingportSwitch#show ring Switchconfig# no ring dualhoming