Husky HME-421E, HME-423E user manual Leave Group, Snmp Configuration, Community Strings, Agent Mode

Page 42

Configuration Using a Web Browser

Leave Group

A message sent by a host to the querier to indicate that the host has quit to be a member of a specific multicast group.

This feature allows the administrator to enable IGMP protocol and IGMP Query function. The administrator will see the IGMP snooping information in this section -- different multicast group VIDs and member ports, and IP multicast addresses range from 224.0.0.0 through 239.255.255.255.

After finishing necessary configurations, click on Apply to save the settings.

4-6.14 SNMP Configuration

Simple Network Management Protocol (SNMP) is used to monitor exchange of information among devices in a network system. HME-421E/423E supports SNMP v1/v2c/v3.

4-6.14.1 Community Strings

This function is to use community strings for authentication.

	Strings	This feature allows the administrator to enter a name for the string.
	RO	RO means Read Only. This feature allows the requests accompanied by
	RO	this string to display MIB-object information.
		this string to display MIB-object information.
	RW	RW means Read & Write. This feature allows the requests accompanied
	RW	by this string to display MIB-object information and to set MIB object.

		This feature allows the administrator to select the SNMP version for
	Agent Mode	necessary configuration. Click on the version option required, and then
		click on Change to validate the settings.

After finishing necessary configurations, click on Apply to save the settings.

4-26

Image 42

Contents HME-421E/423E Copyright Notice Table of Contents Ring Application Couple Ring Dual Homing Dual Ring Page Product Features IntroductionOverview Package Checklist Front Panel Side Panel Hardware InstallationDimensions and Panel Layout Back Panel Bottom PanelLED Name LED Color LED Function LED IndicatorsRJ-45 Ports 1 RJ-45 Pin AssignmentsFiber Ports PinInstalling Your Ethernet Direct Switch Mounting The SwitchDIN-Rail Mounting Wiring The Power Inputs Wall MountingWiring The Fault Alarm Contact CablingPage Login The Console Interface Configuration Using Console InterfaceConnecting Console Port CLI ManagementConfigure Command LevelsModes Access Method Prompt Exit Method About This Mode DatabaseAbout Web-based Management Interface Configuration Using a Web BrowserSystem Login Preparing for Web-based ManagementBasic Settings Management Main ScreenPort Statistics User AuthenticationConfirm password PortIP Configuration Fault Relay AlarmPower Failure Port Link Down/BrokenRestoring Configurations by Tftp Backing up Configurations by TftpUpdating Firmware by Tftp Advanced Management Settings Security SpeedDuplex Rate LimitingSource Port Port MirroringDestination Port Dhcp ServerLease Time sec Low IP AddressHigh IP Address Port and IP Bindings by Dhcp ServerSystem Log Server IP System Event Log Syslog ConfigurationSyslog Client Mode AddressEmail Alert Smtp ConfigurationAuthentication Smtp Server IPEvent Configuration System event selectionPort event selection Daylight Saving Time Sntp ConfigurationSntp Client UTC TimezoneEnable Http Server Mins Switch TimerIP Security Mode Enable Telnet ServerSystem Priority Aggregator SettingsPort Trunking Group IDGroup Key Lacp DisabledAggregator Information Port MemberLacp Enabled State Activity Vlan Configuration Port-based VlanPage Ieee 802.1Q Tag-based Vlan 11.2.1 802.1Q Configuration Vlan Operation ModeEnable Gvrp Management Vlan IDLink Type Untagged VIDTagged VID Group Configuration QoS Policy QoS ConfigurationUse an 8, 4, 2, 1 weighted fair queuing scheme Use the strict priority schemeIgmp Configuration Leave Group Snmp ConfigurationAgent Mode Community StringsCommunity Trap ConfigurationSnmp v3 Configuration Trap VersionContext Table Context Name Group Table Security Name User IDContext Match Rule Access Table Context PrefixSecurity Level Read View NameLldp Configuration Lldp ProtocolLldp Interval Rstp Mode Rapid Spanning Tree Protocol Configuration RstpSystem Configuration Forward Delay TimeAdmin Non Stp Admin P2PAdmin Edge Ring ConfigurationEnable Dual Homing Enable RingEnable Couple Ring Enable Dual RingRadius Server IP 18 802.1X/Radius ConfigurationIeee 802.1x Protocol Server PortReject DisableMisc Configuration AcceptStatic MAC Address Settings Supplicant TimeoutServer Timeout Max RequestsMAC Filtering All MAC AddressesMulticast Filtering Member PortsNetwork Applications Ring ApplicationCouple Ring Dual Homing Example of Couple Ring ConnectionNetwork Applications Example of Dual Ring Connection Diagram Dual RingSpecifications TechnologyRegulatory Approvals Management Specifications Dhcp Troubleshooting Appendix BCommand Set Lists Commands Set ListSystem Commands Set Port Commands Set Broadcast-multicast-flooded-unicast Broadcast-multicastBroadcast-only Trunk Commands Set Vlan Commands SetSwitchvlan#vlanmode 802.1q Switch#vlan databaseSwitchvlan#vlanmode portbase Ported based Vlan configurationSpanning Tree Commands Set QoS Commands Set Igmp Commands SetMac / Filter Table Commands Set Snmp Commands SetGroup G1 password AuthPW PrivPW Switchconfig#snmpv3 context-nameSwitchconfig#snmpv3 user test01 Switchconfig#snmpv3 mibview viewPort Mirroring Commands Set 12 802.1x Commands SetTftp Commands Set SystemLog, Smtp and Event Commands Set Sntp Commands Set Ring Commands SetSwitchconfig# no ring couplering Switchconfig#ring homingportSwitch#show ring Switchconfig# no ring dualhoming