Husky HME-423E, HME-421E user manual QoS Commands Set, Igmp Commands Set

Page 69

Command Set Lists

		set the path cost for
		Spanning Tree Protocol
		(STP) calculations. In the
		event of a loop, spanning
		tree considers the path
		cost when selecting an
		interface to place into the
		forwarding state.
stp-path-priority	I	Use the spanning-tree	switch(config)#interface fastEthernet 2
[Port Priority]		port-priority interface	switch(config-if)#stp-path-priority 128
		configuration command to
		configure a port priority
		that is used when two
		switches tie for position
		as the root switch.
stp-admin-p2p	I	Admin P2P of STP priority	switch(config)#interface fastEthernet 2
[AutoTrueFalse]		on this interface.	switch(config-if)#stp-admin-p2p Auto
stp-admin-edge	I	Admin Edge of STP	switch(config)#interface fastEthernet 2
[TrueFalse]		priority on this interface.	switch(config-if)#stp-admin-edge True
stp-admin-non-stp	I	Admin NonSTP of STP	switch(config)#interface fastEthernet 2
[TrueFalse]		priority on this interface.	switch(config-if)#stp-admin-non-stp
			False
show spanning-tree	E	Displays a summary of	switch>show spanning-tree
		the spanning-tree states.
no spanning-tree	G	Disable spanning-tree.	switch(config)#no spanning-tree

C-7 QoS Commands Set

Commands	Level	Description	Example
qos policy	G	Select QoS policy	switch(config)#qos policy weighted-fair
[weighted-fairstrict]		scheduling
qos prioritytype	G	Set up QoS priority type	switch(config)#qos prioritytype
[port-basedcos-onlytos-onl
ycos-firsttos-first]
qos priority portbased	G	Configure Port-based	switch(config)#qos priority portbased 1
[Port]		priority	low
[lowestlowmiddlehigh]
qos priority cos	G	Configure COS Priority	switch(config)#qos priority cos 0
[Priority][lowestlowmiddleh			middle
igh]			middle
igh]
qos priority tos	G	Configure TOS Priority	switch(config)#qos priority tos 3 high
[Priority][lowestlowmiddleh
igh]
show qos	P	Displays the information	switch#show qos
		of QoS configuration
no qos	G	Disable QoS function	switch(config)#no qos

C-8 IGMP Commands Set

Commands	Level	Description	Example
igmp enable	G	Enable IGMP snooping	switch(config)#igmp enable
		function

C-7

Image 69

Contents HME-421E/423E Copyright Notice Table of Contents Ring Application Couple Ring Dual Homing Dual Ring Page Product Features IntroductionOverview Package Checklist Dimensions and Panel Layout Hardware InstallationFront Panel Side Panel Back Panel Bottom PanelRJ-45 Ports LED IndicatorsLED Name LED Color LED Function 1 RJ-45 Pin AssignmentsPin Fiber PortsInstalling Your Ethernet Direct Switch Mounting The SwitchDIN-Rail Mounting Wall Mounting Wiring The Power InputsCabling Wiring The Fault Alarm ContactPage Connecting Console Port Configuration Using Console InterfaceLogin The Console Interface CLI ManagementModes Access Method Prompt Exit Method About This Mode Command LevelsConfigure DatabaseSystem Login Configuration Using a Web BrowserAbout Web-based Management Interface Preparing for Web-based ManagementManagement Main Screen Basic SettingsConfirm password User AuthenticationPort Statistics PortPower Failure Fault Relay AlarmIP Configuration Port Link Down/BrokenRestoring Configurations by Tftp Backing up Configurations by TftpUpdating Firmware by Tftp Advanced Management Settings Duplex SpeedSecurity Rate LimitingDestination Port Port MirroringSource Port Dhcp ServerHigh IP Address Low IP AddressLease Time sec Port and IP Bindings by Dhcp ServerSyslog Client Mode System Event Log Syslog ConfigurationSystem Log Server IP AddressAuthentication Smtp ConfigurationEmail Alert Smtp Server IPEvent Configuration System event selectionPort event selection Sntp Client Sntp ConfigurationDaylight Saving Time UTC TimezoneIP Security Mode Mins Switch TimerEnable Http Server Enable Telnet ServerPort Trunking Aggregator SettingsSystem Priority Group IDAggregator Information Lacp DisabledGroup Key Port MemberLacp Enabled State Activity Port-based Vlan Vlan ConfigurationPage Enable Gvrp 11.2.1 802.1Q Configuration Vlan Operation ModeIeee 802.1Q Tag-based Vlan Management Vlan IDLink Type Untagged VIDTagged VID Group Configuration Use an 8, 4, 2, 1 weighted fair queuing scheme QoS ConfigurationQoS Policy Use the strict priority schemeIgmp Configuration Agent Mode Snmp ConfigurationLeave Group Community StringsSnmp v3 Configuration Trap ConfigurationCommunity Trap VersionGroup Table Security Name User ID Context Table Context NameSecurity Level Access Table Context PrefixContext Match Rule Read View NameLldp Configuration Lldp ProtocolLldp Interval System Configuration Rapid Spanning Tree Protocol Configuration RstpRstp Mode Forward Delay TimeAdmin Edge Admin P2PAdmin Non Stp Ring ConfigurationEnable Couple Ring Enable RingEnable Dual Homing Enable Dual RingIeee 802.1x Protocol 18 802.1X/Radius ConfigurationRadius Server IP Server PortMisc Configuration DisableReject AcceptServer Timeout Supplicant TimeoutStatic MAC Address Settings Max RequestsAll MAC Addresses MAC FilteringMember Ports Multicast FilteringNetwork Applications Ring ApplicationCouple Ring Example of Couple Ring Connection Dual HomingNetwork Applications Dual Ring Example of Dual Ring Connection DiagramSpecifications TechnologyRegulatory Approvals Management Specifications Dhcp Appendix B TroubleshootingCommand Set Lists Commands Set ListSystem Commands Set Port Commands Set Broadcast-multicast-flooded-unicast Broadcast-multicastBroadcast-only Vlan Commands Set Trunk Commands SetSwitchvlan#vlanmode portbase Switch#vlan databaseSwitchvlan#vlanmode 802.1q Ported based Vlan configurationSpanning Tree Commands Set Igmp Commands Set QoS Commands SetSnmp Commands Set Mac / Filter Table Commands SetSwitchconfig#snmpv3 user test01 Switchconfig#snmpv3 context-nameGroup G1 password AuthPW PrivPW Switchconfig#snmpv3 mibview view12 802.1x Commands Set Port Mirroring Commands SetTftp Commands Set SystemLog, Smtp and Event Commands Set Ring Commands Set Sntp Commands SetSwitch#show ring Switchconfig#ring homingportSwitchconfig# no ring couplering Switchconfig# no ring dualhoming