Husky HME-421E 18 802.1X/Radius Configuration, Ieee 802.1x Protocol, Radius Server IP, Shared Key

Page 50

Configuration Using a Web Browser

When the X-Ring function is enabled, RSTP function must be disabled. The X-Ring function and RSTP function cannot be in operation at the same time.

4-6.18 802.1X/Radius Configuration

802.1X is an IEEE standard, which provides port-based authentication. It involves communications between a supplicant, authenticator, and authentication server. The supplicant is often software on a client device, such as a laptop, the authenticator is a wired Ethernet switch or wireless access point, and an authentication server is generally a RADIUS database. The authenticator acts like a security guard to a protected network. The supplicant (i.e., client device) is not allowed access through the authenticator to the protected side of the network until the supplicant’s identity is authorized.

4-6.18.1 System Configuration

The administrator can use this interface to enable and configure 802.1X/Radius security function.

	IEEE 802.1x Protocol	This feature is to enable or disable IEEE 802.1X protocol.
	Radius Server IP	This feature is to assign the RADIUS Server IP address.
	Server Port	This feature is to set the UDP destination port for authentication requests
	Server Port	to the specified RADIUS Server.
		to the specified RADIUS Server.
	Accounting Port	This feature is to set the UDP destination port for accounting requests to
	Accounting Port	the specified RADIUS Server.
		the specified RADIUS Server.
		This feature is to set an encryption key for authentication with the
	Shared Key	specified RADIUS server. This key must match the encryption key used
		on the RADIUS Server.
	NAS, Identifier	This feature is to assign the identifier for the RADIUS client.

4-34

Image 50

Contents HME-421E/423E Copyright Notice Table of Contents Ring Application Couple Ring Dual Homing Dual Ring Page Overview Product FeaturesIntroduction Package Checklist Front Panel Side Panel Hardware InstallationDimensions and Panel Layout Back Panel Bottom PanelLED Name LED Color LED Function LED IndicatorsRJ-45 Ports 1 RJ-45 Pin AssignmentsFiber Ports PinDIN-Rail Mounting Installing Your Ethernet Direct SwitchMounting The Switch Wiring The Power Inputs Wall MountingWiring The Fault Alarm Contact CablingPage Login The Console Interface Configuration Using Console InterfaceConnecting Console Port CLI ManagementConfigure Command LevelsModes Access Method Prompt Exit Method About This Mode DatabaseAbout Web-based Management Interface Configuration Using a Web BrowserSystem Login Preparing for Web-based ManagementBasic Settings Management Main ScreenPort Statistics User AuthenticationConfirm password PortIP Configuration Fault Relay AlarmPower Failure Port Link Down/BrokenUpdating Firmware by Tftp Restoring Configurations by TftpBacking up Configurations by Tftp Advanced Management Settings Security SpeedDuplex Rate LimitingSource Port Port MirroringDestination Port Dhcp ServerLease Time sec Low IP AddressHigh IP Address Port and IP Bindings by Dhcp ServerSystem Log Server IP System Event Log Syslog ConfigurationSyslog Client Mode AddressEmail Alert Smtp ConfigurationAuthentication Smtp Server IPPort event selection Event ConfigurationSystem event selection Daylight Saving Time Sntp ConfigurationSntp Client UTC TimezoneEnable Http Server Mins Switch TimerIP Security Mode Enable Telnet ServerSystem Priority Aggregator SettingsPort Trunking Group IDGroup Key Lacp DisabledAggregator Information Port MemberLacp Enabled State Activity Vlan Configuration Port-based VlanPage Ieee 802.1Q Tag-based Vlan 11.2.1 802.1Q Configuration Vlan Operation ModeEnable Gvrp Management Vlan IDTagged VID Link TypeUntagged VID Group Configuration QoS Policy QoS ConfigurationUse an 8, 4, 2, 1 weighted fair queuing scheme Use the strict priority schemeIgmp Configuration Leave Group Snmp ConfigurationAgent Mode Community StringsCommunity Trap ConfigurationSnmp v3 Configuration Trap VersionContext Table Context Name Group Table Security Name User IDContext Match Rule Access Table Context PrefixSecurity Level Read View NameLldp Interval Lldp ConfigurationLldp Protocol Rstp Mode Rapid Spanning Tree Protocol Configuration RstpSystem Configuration Forward Delay TimeAdmin Non Stp Admin P2PAdmin Edge Ring ConfigurationEnable Dual Homing Enable RingEnable Couple Ring Enable Dual RingRadius Server IP 18 802.1X/Radius ConfigurationIeee 802.1x Protocol Server PortReject DisableMisc Configuration AcceptStatic MAC Address Settings Supplicant TimeoutServer Timeout Max RequestsMAC Filtering All MAC AddressesMulticast Filtering Member PortsCouple Ring Network ApplicationsRing Application Dual Homing Example of Couple Ring ConnectionNetwork Applications Example of Dual Ring Connection Diagram Dual RingRegulatory Approvals SpecificationsTechnology Management Specifications Dhcp Troubleshooting Appendix BSystem Commands Set Command Set ListsCommands Set List Port Commands Set Broadcast-only Broadcast-multicast-flooded-unicastBroadcast-multicast Trunk Commands Set Vlan Commands SetSwitchvlan#vlanmode 802.1q Switch#vlan databaseSwitchvlan#vlanmode portbase Ported based Vlan configurationSpanning Tree Commands Set QoS Commands Set Igmp Commands SetMac / Filter Table Commands Set Snmp Commands SetGroup G1 password AuthPW PrivPW Switchconfig#snmpv3 context-nameSwitchconfig#snmpv3 user test01 Switchconfig#snmpv3 mibview viewPort Mirroring Commands Set 12 802.1x Commands SetTftp Commands Set SystemLog, Smtp and Event Commands Set Sntp Commands Set Ring Commands SetSwitchconfig# no ring couplering Switchconfig#ring homingportSwitch#show ring Switchconfig# no ring dualhoming