Cabletron Systems EMM-E6 manual Repeater-level Security and Traps, Channel X Security Window

Page 100

Security

Repeater-level Security and Traps

Locking ports at the repeater, or channel, level applies all applicable security (as configured via the Port Security window) to every port on the channel.

NOTE

If you select a repeater whose ports have different security capabilities, you may still be able to select and apply security states which are not applicable to all ports. Applying these kinds of settings will have no adverse affect on your network devices: those ports which can accept the set will do so; those which cannot will either ignore the set or issue a Set Failed.

To enable or disable security and traps for all ports on a repeater:

1.In the Repeater Security window, click mouse button 1 on the repeater interface for which you would like to configure port locking and/or traps.

2.Click mouse button 1 on ; the Channel X Security window, Figure 7-5, will appear. Note that the current repeater-level settings are displayed immediately to the right of the field names; a repeater whose ports have different Security Mode or Trap settings will display a status of “Mismatch.”

Figure 7-5. Channel X Security Window

3.In the Security Mode field, click mouse button 1 on the appropriate selection to apply Full or Continuous lock status to all ports on the selected repeater channel, or to Unlock all ports on the channel. (Note that if your EMM-E6 does not support the newest security enhancements, the Continuous selection will be unavailable.)

4.In the Send Trap field, click mouse button 1 on the appropriate selection to Enable or Disable traps for the selected repeater channel.

7-14

Enabling Security and Traps

Image 100
Contents EMM-E6 Page Virus Disclaimer Restricted Rights Notice Contents Chapter Source Addressing Chapter SecurityChapter Front Panel Redundancy Appendix a EMM-E6 MIB StructureContents Using the EMM-E6 User’s Guide IntroductionUsing the EMM-E6 User’s Guide What’s not in the EMM-E6 User’s Guide UPSConventions Screen Displays Window ConventionsUsing the Mouse ButtonGetting Help EMM-E6 Firmware Year 2000 ComplianceUsing the EMM-E6 Hub View Using the Hub ViewNavigating Through the Hub View Hub View Front PanelUptime Date and TimeDevice Name Device LocationUsing the EMM-E6 Hub View EMM-E6 Ports Display Using the Mouse in a Hub View Module Brim PortsHub View Port Color Codes Port Display FormMonitoring Hub Performance Port Display Form Errors LoadTraffic CollisionsFrame Sizes ProtocolsPort Type Using the EMM-E6 Hub View Name and Location Checking Device Status and Updating Front Panel InfoContact Checking Network Status Chassis TypeName Active UsersChecking Module Status Module TypeChecking Port Status Link StatusStatus Media TypeViewing the IP Address Table Topology TypeLaunching the Global Find MAC Address Tool Checking StatisticsUsing the EMM-E6 Hub View Received Bytes Total PacketsAvg Packet Size Broadcast PacketsTotal Errors Alignment ErrorsCRC Errors OOW CollisionsRunt Frames Giant FramesViewing the Port Source Address List Protocols/Frames StatisticsUsing the EMM-E6 Hub View Setting the Polling Intervals Managing the HubContact Status Device General StatusConfiguring FNB Connections Device ConfigurationPort Operational State StatisticsConfiguring RIC MIM Connections To configure FNB connectivity for an individual port Setting a Port’s Trunk Type 15. Tpxmim Channel Selection WindowTo change a port’s topology status Enabling/Disabling MIM Ports Alarm Configuration Using Alarm Configuration From the command line stand-alone modeFrom the icon From the Hub ViewConfiguring Alarms CRCSetting Repeater Alarms BroadcastSetting and Changing Alarms Set Repeater Alarms WindowSetting Module and Port Alarms Setting Module AlarmsSet Module Alarms Window Set the Status to EnabledSetting Port Alarms Set Port Alarms WindowSet the Status to Enabled Alarm Configuration Setting Module and Port Alarms What is a Segmentation Trap? Link/Seg TrapsWhat is a Link Trap? Enabling and Disabling Link/Seg TrapsSpmarun r4hwtr IP address community name Configuring Link/Seg Traps for the Repeater Viewing and Configuring Link/Seg Traps for Hub ModulesModule Traps Window Viewing and Configuring Link/Seg Traps for Ports Port Traps WindowLink/Seg Traps Link/Seg Traps Enabling and Disabling Link/Seg Traps Setting Network Circuit Redundancy Repeater RedundancyConfiguring a Redundant Circuit Spmarun r4red IP address community nameChannel X Redundancy Window Add Circuit Address Window Repeater Redundancy Monitoring Redundancy To set the Poll IntervalSource Addressing Displaying the Source Address ListDisplaying the Source Address List Source Addressing Setting the Hash Type Setting the Aging TimeLocking Source Addresses Source Address Locking on Older Devices Configuring Source Address Traps Repeater-level Traps Module- and Port-level Traps Source Addressing Finding a Source Address Port Source Address Traps WindowClick on to exit the window Security What is LANVIEWSECURE? Spmarun r4sec IP address SU community nameSecure address assignment New definitions for station and trunk portsTrunk port security Newest Lanviewsecure Features Continuous learning modeConfigurable violation response Full or partial security against eavesdroppingSecurity on Non-LANVIEWSECUREMIMs Learned addresses resetForced non-secure status Configuring Security Security To assign secure addresses to a port Addresses Window Boards with Multiple Caches Add MAC Address WindowResetting Learned Addresses Tips for Successfully Implementing Eavesdropper ProtectionEnabling Security and Traps Security Repeater-level Security and Traps Channel X Security WindowModule-level Security and Traps Channel X Module Security Window Port-level Security and Traps Channel X Port Security WindowSecurity Setting Front Panel Redundancy Front Panel RedundancySetting Front Panel Redundancy Add Circuit Address Window Front Panel Redundancy Setting Front Panel Redundancy Ietf MIB Support EMM-E6 MIB StructureMIB Components Chassis MGRHost Services IP ServicesRepeater One, Repeater Two, and Repeater Three Ctron Use OnlyRmon Default Distributed LAN MonitorMIB Navigator Rmon HostBrief Word About MIB Components and Community Names EMM-E6 MIB Structure Index Index-2 Index-3 Index Index-4
Related manuals
Manual 64 pages 974 b