Cabletron Systems EMM-E6 manual Source Addressing

Page 84

Source Addressing

Figure 6-3. The Module Source Address Traps Window

To enable or disable port-level traps:

1.In the Port Source Address Traps window (Figure 6-4, below), click mouse button 1 to select the port or ports for which you wish to enable or disable traps. If the Set Trap Status For field displaysSelected Ports (the default setting), you can click to select any ports; to de-select any highlighted port, click on it again. If the selection All Ports On Module is displayed in the Set Traps Status For field, you can select only one port at a time; trap status will be set for all ports on the same module as the selected port. If the selection All Ports on Repeater is displayed in the Set Trap Status For field, all available ports will be automatically selected; if you de-select any port, the Set Trap Status For field will automatically revert to theSelected Ports setting. To change the setting in the Set Trap Status For field, click mouse button 1 on the currently displayed setting, and drag down to select a new setting.

6-10

Configuring Source Address Traps

Page 83 Page 85
Image 84
Page 83 Page 85
Contents EMM-E6 Page Virus Disclaimer Restricted Rights Notice Contents Chapter Source Addressing Chapter SecurityChapter Front Panel Redundancy Appendix a EMM-E6 MIB StructureContents Using the EMM-E6 User’s Guide IntroductionUsing the EMM-E6 User’s Guide What’s not in the EMM-E6 User’s Guide UPSConventions Screen Displays Window ConventionsUsing the Mouse ButtonGetting Help EMM-E6 Firmware Year 2000 ComplianceUsing the EMM-E6 Hub View Using the Hub ViewNavigating Through the Hub View Hub View Front PanelUptime Date and TimeDevice Name Device LocationUsing the EMM-E6 Hub View EMM-E6 Ports Display Using the Mouse in a Hub View Module Brim PortsHub View Port Color Codes Port Display FormMonitoring Hub Performance Port Display Form Errors LoadTraffic CollisionsProtocols Frame SizesPort Type Using the EMM-E6 Hub View Checking Device Status and Updating Front Panel Info Name and LocationContact Checking Network Status Chassis TypeName Active UsersChecking Module Status Module TypeChecking Port Status Link StatusStatus Media TypeViewing the IP Address Table Topology TypeLaunching the Global Find MAC Address Tool Checking StatisticsUsing the EMM-E6 Hub View Received Bytes Total PacketsAvg Packet Size Broadcast PacketsTotal Errors Alignment ErrorsCRC Errors OOW CollisionsRunt Frames Giant FramesViewing the Port Source Address List Protocols/Frames StatisticsUsing the EMM-E6 Hub View Setting the Polling Intervals Managing the HubContact Status Device General StatusConfiguring FNB Connections Device ConfigurationPort Operational State StatisticsConfiguring RIC MIM Connections To configure FNB connectivity for an individual port Setting a Port’s Trunk Type 15. Tpxmim Channel Selection WindowTo change a port’s topology status Enabling/Disabling MIM Ports Alarm Configuration Using Alarm Configuration From the command line stand-alone modeFrom the icon From the Hub ViewConfiguring Alarms CRCSetting Repeater Alarms BroadcastSetting and Changing Alarms Set Repeater Alarms WindowSetting Module and Port Alarms Setting Module AlarmsSet Module Alarms Window Set the Status to EnabledSetting Port Alarms Set Port Alarms WindowSet the Status to Enabled Alarm Configuration Setting Module and Port Alarms What is a Segmentation Trap? Link/Seg TrapsWhat is a Link Trap? Enabling and Disabling Link/Seg TrapsSpmarun r4hwtr IP address community name Configuring Link/Seg Traps for the Repeater Viewing and Configuring Link/Seg Traps for Hub ModulesModule Traps Window Viewing and Configuring Link/Seg Traps for Ports Port Traps WindowLink/Seg Traps Link/Seg Traps Enabling and Disabling Link/Seg Traps Setting Network Circuit Redundancy Repeater RedundancyConfiguring a Redundant Circuit Spmarun r4red IP address community nameChannel X Redundancy Window Add Circuit Address Window Repeater Redundancy Monitoring Redundancy To set the Poll IntervalSource Addressing Displaying the Source Address ListDisplaying the Source Address List Source Addressing Setting the Hash Type Setting the Aging TimeLocking Source Addresses Source Address Locking on Older Devices Configuring Source Address Traps Repeater-level Traps Module- and Port-level Traps Source Addressing Finding a Source Address Port Source Address Traps WindowClick on to exit the window Security What is LANVIEWSECURE? Spmarun r4sec IP address SU community nameNew definitions for station and trunk ports Secure address assignmentTrunk port security Newest Lanviewsecure Features Continuous learning modeConfigurable violation response Full or partial security against eavesdroppingLearned addresses reset Security on Non-LANVIEWSECUREMIMsForced non-secure status Configuring Security Security To assign secure addresses to a port Addresses Window Boards with Multiple Caches Add MAC Address WindowResetting Learned Addresses Tips for Successfully Implementing Eavesdropper ProtectionEnabling Security and Traps Security Repeater-level Security and Traps Channel X Security WindowModule-level Security and Traps Channel X Module Security Window Port-level Security and Traps Channel X Port Security WindowSecurity Setting Front Panel Redundancy Front Panel RedundancySetting Front Panel Redundancy Add Circuit Address Window Front Panel Redundancy Setting Front Panel Redundancy Ietf MIB Support EMM-E6 MIB StructureMIB Components Chassis MGRHost Services IP ServicesRepeater One, Repeater Two, and Repeater Three Ctron Use OnlyRmon Default Distributed LAN MonitorMIB Navigator Rmon HostBrief Word About MIB Components and Community Names EMM-E6 MIB Structure Index Index-2 Index-3 Index Index-4
Related manuals
Manual 64 pages 974 b
Top Page Image Contents