Cabletron Systems EMM-E6 manual What is LANVIEWSECURE?, Spmarun r4sec IP address SU community name

Page 88

Security

from the command line (stand-alone mode):

1.From the appropriate directory, type

spmarun r4sec <IP address> <SU community name>

NOTES

The spmarun script invoked ﬁrst in the above command temporarily sets the environment variables SPMA needs to operate; be sure to use this command any time you launch an application from the command line. This script is automatically invoked when you launch an application from the icon menu or from within the Hub View.

You must use a community name with Superuser access to run the Security application.

If there is a hostname mapped to your EMM-E6’s IP address, you can use <hostname> in place of <IP address> to launch this application. Please note, however, that the hostname is not the same as the device name which can be assigned via Local Management and/or SPMA; you cannot use the device name in place of the IP address.

The Repeater Security window, Figure 7-1, will appear.

Figure 7-1. The Repeater Security Window

The Repeater Security window provides a list of the repeater interfaces available on the EMM-E6, as well as command buttons that allow you to conﬁgure security at the repeater, module, and port levels.

What is LANVIEWSECURE?

LANVIEWSECURE comprises a set of enhanced security features that have been implemented on the new generation of Cabletron’s repeater MIM family (as designated by the letter “S” at the end of the module name); these features are supported beginning with EMM-E6 ﬁrmware version 2.00.16, with the newest enhancements supported by ﬁrmware versions 3.11.xx and later.

7-2	What is LANVIEWsecure?

Image 88

Contents EMM-E6 Page Virus Disclaimer Restricted Rights Notice Contents Chapter Source Addressing Chapter SecurityChapter Front Panel Redundancy Appendix a EMM-E6 MIB StructureContents Using the EMM-E6 User’s Guide IntroductionUsing the EMM-E6 User’s Guide What’s not in the EMM-E6 User’s Guide UPSConventions Screen Displays Window ConventionsUsing the Mouse ButtonGetting Help EMM-E6 Firmware Year 2000 ComplianceUsing the EMM-E6 Hub View Using the Hub ViewNavigating Through the Hub View Hub View Front PanelUptime Date and TimeDevice Name Device LocationUsing the EMM-E6 Hub View EMM-E6 Ports Display Using the Mouse in a Hub View Module Brim PortsHub View Port Color Codes Port Display FormMonitoring Hub Performance Port Display Form Errors LoadTrafﬁc CollisionsFrame Sizes ProtocolsPort Type Using the EMM-E6 Hub View Name and Location Checking Device Status and Updating Front Panel InfoContact Checking Network Status Chassis TypeName Active UsersChecking Module Status Module TypeChecking Port Status Link StatusStatus Media TypeViewing the IP Address Table Topology TypeLaunching the Global Find MAC Address Tool Checking StatisticsUsing the EMM-E6 Hub View Received Bytes Total PacketsAvg Packet Size Broadcast PacketsTotal Errors Alignment ErrorsCRC Errors OOW CollisionsRunt Frames Giant FramesViewing the Port Source Address List Protocols/Frames StatisticsUsing the EMM-E6 Hub View Setting the Polling Intervals Managing the HubContact Status Device General StatusConﬁguring FNB Connections Device ConﬁgurationPort Operational State StatisticsConﬁguring RIC MIM Connections To conﬁgure FNB connectivity for an individual port Setting a Port’s Trunk Type 15. Tpxmim Channel Selection WindowTo change a port’s topology status Enabling/Disabling MIM Ports Alarm Conﬁguration Using Alarm Conﬁguration From the command line stand-alone modeFrom the icon From the Hub ViewConﬁguring Alarms CRCSetting Repeater Alarms BroadcastSetting and Changing Alarms Set Repeater Alarms WindowSetting Module and Port Alarms Setting Module AlarmsSet Module Alarms Window Set the Status to EnabledSetting Port Alarms Set Port Alarms WindowSet the Status to Enabled Alarm Conﬁguration Setting Module and Port Alarms What is a Segmentation Trap? Link/Seg TrapsWhat is a Link Trap? Enabling and Disabling Link/Seg TrapsSpmarun r4hwtr IP address community name Conﬁguring Link/Seg Traps for the Repeater Viewing and Conﬁguring Link/Seg Traps for Hub ModulesModule Traps Window Viewing and Conﬁguring Link/Seg Traps for Ports Port Traps WindowLink/Seg Traps Link/Seg Traps Enabling and Disabling Link/Seg Traps Setting Network Circuit Redundancy Repeater RedundancyConﬁguring a Redundant Circuit Spmarun r4red IP address community nameChannel X Redundancy Window Add Circuit Address Window Repeater Redundancy Monitoring Redundancy To set the Poll IntervalSource Addressing Displaying the Source Address ListDisplaying the Source Address List Source Addressing Setting the Hash Type Setting the Aging TimeLocking Source Addresses Source Address Locking on Older Devices Conﬁguring Source Address Traps Repeater-level Traps Module- and Port-level Traps Source Addressing Finding a Source Address Port Source Address Traps WindowClick on to exit the window Security What is LANVIEWSECURE? Spmarun r4sec IP address SU community nameSecure address assignment New deﬁnitions for station and trunk portsTrunk port security Newest Lanviewsecure Features Continuous learning modeConﬁgurable violation response Full or partial security against eavesdroppingSecurity on Non-LANVIEWSECUREMIMs Learned addresses resetForced non-secure status Conﬁguring Security Security To assign secure addresses to a port Addresses Window Boards with Multiple Caches Add MAC Address WindowResetting Learned Addresses Tips for Successfully Implementing Eavesdropper ProtectionEnabling Security and Traps Security Repeater-level Security and Traps Channel X Security WindowModule-level Security and Traps Channel X Module Security Window Port-level Security and Traps Channel X Port Security WindowSecurity Setting Front Panel Redundancy Front Panel RedundancySetting Front Panel Redundancy Add Circuit Address Window Front Panel Redundancy Setting Front Panel Redundancy Ietf MIB Support EMM-E6 MIB StructureMIB Components Chassis MGRHost Services IP ServicesRepeater One, Repeater Two, and Repeater Three Ctron Use OnlyRmon Default Distributed LAN MonitorMIB Navigator Rmon HostBrief Word About MIB Components and Community Names EMM-E6 MIB Structure Index Index-2 Index-3 Index Index-4

Related manuals

Manual 64 pages 974 b