Cabletron Systems EMM-E6 manual Set the Status to Enabled

Page 59

Alarm Configuration

3.Select one or more ports in the scroll list. To apply one set of conditions to all ports, you can either select each port in the list or use the Set Alarm For box at the bottom of the window to choose either Selected Ports, which applies the conditions to the ports you selected in the port list, or All Ports on Repeater, which applies the conditions to all the ports on the repeater, or All Ports on Module, which applies the conditions to all the ports on the module.

4.Click mouse button 1 on one of the four Alarm Types: Collisions, Errors, Traffic, or Broadcast. (Alarm Types not available for this device are grayed.) If you select Errors, the Mask check boxes become active and you can select all or just some of the five error types. The Error MaskCARGO, displayed in the module list, is an acronym for the error types: C = CRC, A = Alignment, R = Runts, G = Giants, O = OOW Collisions.

5.Set the Status to Enabled.

6.Highlight and edit the Alarm Threshold, which is the percentage of errors/total packets, or the number of traffic packets, broadcast packets, or collisions/good packet within the Timebase that will activate the alarm.

7.If you select Yes for Disable Port on Alarm, the defined condition will cause the device to disable the port.

NOTE

If a port is disabled by an alarm, you must manually re-enable the port before it can again pass traffic. Resetting the device does not re-enable the port.

8. Click mouse button 1 on .

NOTE

The Timebase applies to all enabled alarms, Port-level and module-level alarms as well as repeater-level alarms. The Timebase appears in each alarms window, repeater, module, and port, but you can only edit it in the Repeater Alarms window.

Setting Module and Port Alarms

3-9

Image 59
Contents EMM-E6 Page Virus Disclaimer Restricted Rights Notice Contents Chapter Security Chapter Source AddressingAppendix a EMM-E6 MIB Structure Chapter Front Panel RedundancyContents Introduction Using the EMM-E6 User’s GuideUsing the EMM-E6 User’s Guide UPS What’s not in the EMM-E6 User’s GuideConventions Window Conventions Screen DisplaysButton Using the MouseGetting Help Year 2000 Compliance EMM-E6 FirmwareUsing the Hub View Using the EMM-E6 Hub ViewHub View Front Panel Navigating Through the Hub ViewDevice Location UptimeDate and Time Device NameUsing the EMM-E6 Hub View EMM-E6 Ports Display Brim Ports Using the Mouse in a Hub View ModulePort Display Form Hub View Port Color CodesMonitoring Hub Performance Port Display Form Collisions ErrorsLoad TrafficPort Type ProtocolsFrame Sizes Using the EMM-E6 Hub View Contact Checking Device Status and Updating Front Panel InfoName and Location Chassis Type Checking Network StatusActive Users NameModule Type Checking Module StatusLink Status Checking Port StatusMedia Type StatusTopology Type Viewing the IP Address TableChecking Statistics Launching the Global Find MAC Address ToolUsing the EMM-E6 Hub View Broadcast Packets Received BytesTotal Packets Avg Packet SizeOOW Collisions Total ErrorsAlignment Errors CRC ErrorsGiant Frames Runt FramesProtocols/Frames Statistics Viewing the Port Source Address ListUsing the EMM-E6 Hub View Managing the Hub Setting the Polling IntervalsDevice General Status Contact StatusStatistics Configuring FNB ConnectionsDevice Configuration Port Operational StateConfiguring RIC MIM Connections To configure FNB connectivity for an individual port 15. Tpxmim Channel Selection Window Setting a Port’s Trunk TypeTo change a port’s topology status Enabling/Disabling MIM Ports Alarm Configuration From the Hub View Using Alarm ConfigurationFrom the command line stand-alone mode From the iconCRC Configuring AlarmsBroadcast Setting Repeater AlarmsSet Repeater Alarms Window Setting and Changing AlarmsSetting Module Alarms Setting Module and Port AlarmsSet the Status to Enabled Set Module Alarms WindowSet Port Alarms Window Setting Port AlarmsSet the Status to Enabled Alarm Configuration Setting Module and Port Alarms Link/Seg Traps What is a Segmentation Trap?Enabling and Disabling Link/Seg Traps What is a Link Trap?Spmarun r4hwtr IP address community name Viewing and Configuring Link/Seg Traps for Hub Modules Configuring Link/Seg Traps for the RepeaterModule Traps Window Port Traps Window Viewing and Configuring Link/Seg Traps for PortsLink/Seg Traps Link/Seg Traps Enabling and Disabling Link/Seg Traps Repeater Redundancy Setting Network Circuit RedundancySpmarun r4red IP address community name Configuring a Redundant CircuitChannel X Redundancy Window Add Circuit Address Window Repeater Redundancy To set the Poll Interval Monitoring RedundancyDisplaying the Source Address List Source AddressingDisplaying the Source Address List Source Addressing Setting the Aging Time Setting the Hash TypeLocking Source Addresses Source Address Locking on Older Devices Configuring Source Address Traps Repeater-level Traps Module- and Port-level Traps Source Addressing Port Source Address Traps Window Finding a Source AddressClick on to exit the window Security Spmarun r4sec IP address SU community name What is LANVIEWSECURE?Trunk port security New definitions for station and trunk portsSecure address assignment Full or partial security against eavesdropping Newest Lanviewsecure FeaturesContinuous learning mode Configurable violation responseForced non-secure status Learned addresses resetSecurity on Non-LANVIEWSECUREMIMs Configuring Security Security To assign secure addresses to a port Addresses Window Add MAC Address Window Boards with Multiple CachesTips for Successfully Implementing Eavesdropper Protection Resetting Learned AddressesEnabling Security and Traps Security Channel X Security Window Repeater-level Security and TrapsModule-level Security and Traps Channel X Module Security Window Channel X Port Security Window Port-level Security and TrapsSecurity Front Panel Redundancy Setting Front Panel RedundancySetting Front Panel Redundancy Add Circuit Address Window Front Panel Redundancy Setting Front Panel Redundancy EMM-E6 MIB Structure Ietf MIB SupportChassis MGR MIB ComponentsCtron Use Only Host ServicesIP Services Repeater One, Repeater Two, and Repeater ThreeRmon Host Rmon DefaultDistributed LAN Monitor MIB NavigatorBrief Word About MIB Components and Community Names EMM-E6 MIB Structure Index Index-2 Index-3 Index Index-4
Related manuals
Manual 64 pages 974 b