Cabletron Systems EMM-E6 manual Monitoring Redundancy, To set the Poll Interval

Page 74

Repeater Redundancy

Monitoring Redundancy

Once you have configured your redundant circuits, you can use the fields in the All Circuits box to set the parameters that the EMM-E6 uses to periodically test each of the circuits. The EMM-E6 automatically polls all enabled circuits through the Primary port and all Backup ports at the time specified in the Test Time box. If the first poll fails (results in a no link condition with all of the circuit IP addresses), the EMM-E6 checks the circuit’s Retries field. If Retries is greater than 0, the EMM-E6 waits the number of seconds specified in the Poll Interval field, and then polls the circuit again.

To set the Poll Interval:

1.In the All Circuits box, type in a new value in the Poll Interval field and click . Poll Interval is the time in seconds between retries (if the first attempt is unsuccessful).

To set the Test Time:

1.In the All Circuits box, type a new test time in the Test Time field in a 24-hour

HH:MM:SS format and click . The Test Time is the time of day when the EMM-E6 polls the addresses listed in each of the enabled circuits.

To immediately test all enabled circuits:

1. Click in the All Circuits box.

5-6

Monitoring Redundancy

Image 74
Contents EMM-E6 Page Virus Disclaimer Restricted Rights Notice Contents Chapter Source Addressing Chapter SecurityChapter Front Panel Redundancy Appendix a EMM-E6 MIB StructureContents Using the EMM-E6 User’s Guide IntroductionUsing the EMM-E6 User’s Guide What’s not in the EMM-E6 User’s Guide UPSConventions Screen Displays Window ConventionsUsing the Mouse ButtonGetting Help EMM-E6 Firmware Year 2000 ComplianceUsing the EMM-E6 Hub View Using the Hub ViewNavigating Through the Hub View Hub View Front PanelDevice Name UptimeDate and Time Device LocationUsing the EMM-E6 Hub View EMM-E6 Ports Display Using the Mouse in a Hub View Module Brim PortsHub View Port Color Codes Port Display FormMonitoring Hub Performance Port Display Form Traffic ErrorsLoad CollisionsPort Type ProtocolsFrame Sizes Using the EMM-E6 Hub View Contact Checking Device Status and Updating Front Panel InfoName and Location Checking Network Status Chassis TypeName Active UsersChecking Module Status Module TypeChecking Port Status Link StatusStatus Media TypeViewing the IP Address Table Topology TypeLaunching the Global Find MAC Address Tool Checking StatisticsUsing the EMM-E6 Hub View Avg Packet Size Received BytesTotal Packets Broadcast PacketsCRC Errors Total ErrorsAlignment Errors OOW CollisionsRunt Frames Giant FramesViewing the Port Source Address List Protocols/Frames StatisticsUsing the EMM-E6 Hub View Setting the Polling Intervals Managing the HubContact Status Device General StatusPort Operational State Configuring FNB ConnectionsDevice Configuration StatisticsConfiguring RIC MIM Connections To configure FNB connectivity for an individual port Setting a Port’s Trunk Type 15. Tpxmim Channel Selection WindowTo change a port’s topology status Enabling/Disabling MIM Ports Alarm Configuration From the icon Using Alarm ConfigurationFrom the command line stand-alone mode From the Hub ViewConfiguring Alarms CRCSetting Repeater Alarms BroadcastSetting and Changing Alarms Set Repeater Alarms WindowSetting Module and Port Alarms Setting Module AlarmsSet Module Alarms Window Set the Status to EnabledSetting Port Alarms Set Port Alarms WindowSet the Status to Enabled Alarm Configuration Setting Module and Port Alarms What is a Segmentation Trap? Link/Seg TrapsWhat is a Link Trap? Enabling and Disabling Link/Seg TrapsSpmarun r4hwtr IP address community name Configuring Link/Seg Traps for the Repeater Viewing and Configuring Link/Seg Traps for Hub ModulesModule Traps Window Viewing and Configuring Link/Seg Traps for Ports Port Traps WindowLink/Seg Traps Link/Seg Traps Enabling and Disabling Link/Seg Traps Setting Network Circuit Redundancy Repeater RedundancyConfiguring a Redundant Circuit Spmarun r4red IP address community nameChannel X Redundancy Window Add Circuit Address Window Repeater Redundancy Monitoring Redundancy To set the Poll IntervalSource Addressing Displaying the Source Address ListDisplaying the Source Address List Source Addressing Setting the Hash Type Setting the Aging TimeLocking Source Addresses Source Address Locking on Older Devices Configuring Source Address Traps Repeater-level Traps Module- and Port-level Traps Source Addressing Finding a Source Address Port Source Address Traps WindowClick on to exit the window Security What is LANVIEWSECURE? Spmarun r4sec IP address SU community nameTrunk port security New definitions for station and trunk portsSecure address assignment Configurable violation response Newest Lanviewsecure FeaturesContinuous learning mode Full or partial security against eavesdroppingForced non-secure status Learned addresses resetSecurity on Non-LANVIEWSECUREMIMs Configuring Security Security To assign secure addresses to a port Addresses Window Boards with Multiple Caches Add MAC Address WindowResetting Learned Addresses Tips for Successfully Implementing Eavesdropper ProtectionEnabling Security and Traps Security Repeater-level Security and Traps Channel X Security WindowModule-level Security and Traps Channel X Module Security Window Port-level Security and Traps Channel X Port Security WindowSecurity Setting Front Panel Redundancy Front Panel RedundancySetting Front Panel Redundancy Add Circuit Address Window Front Panel Redundancy Setting Front Panel Redundancy Ietf MIB Support EMM-E6 MIB StructureMIB Components Chassis MGRRepeater One, Repeater Two, and Repeater Three Host ServicesIP Services Ctron Use OnlyMIB Navigator Rmon DefaultDistributed LAN Monitor Rmon HostBrief Word About MIB Components and Community Names EMM-E6 MIB Structure Index Index-2 Index-3 Index Index-4
Related manuals
Manual 64 pages 974 b