Cabletron Systems EMM-E6 manual Module- and Port-level Traps

Page 83

Source Addressing

Module- and Port-level Traps

To set module- and port-level source addressing traps, select the appropriate

channel in the Repeater Source Address window, then click on to

enable and disable module-level traps, or onto enable and disable port-level traps.

NOTE

It is not necessary to close the Source Address List before launching the module and port traps windows; just move the Source Address List window out of the way, if necessary, to reach the main Repeater Source Address window.

As with repeater-level trap status, a status of Other for any module indicates that there is some combination of enabled and disabled source address traps on the ports in that module.

To configure trap status for all ports on a selected module or modules:

1.In the Module Source Address Traps window (Figure 6-3, next page), click mouse button 1 to select the module for which you wish to enable or disable traps. If the Set Trap Status For field displaysSelected Modules (the default setting), you can click to select any modules; to de-select any highlighted module, click on it again. If the selection All Modules is displayed in the Set Trap Status For field, all available modules will be automatically selected; if you de-select any module, the Set Trap Status For field will automatically revert to the Selected Modules setting. To change the setting in the Set Trap Status For field, click mouse button 1 on the currently displayed setting, and drag down to select a new setting.

2.Click on the appropriate selection in the Trap Status field to enable or disable traps for the selected modules, as desired.

3.Click on to save your changes. Note that enabling or disabling traps at the module level will eliminate any module status of Other by setting all ports on the selected module or modules to the same status.

Configuring Source Address Traps

6-9

Image 83
Contents EMM-E6 Page Virus Disclaimer Restricted Rights Notice Contents Chapter Security Chapter Source AddressingAppendix a EMM-E6 MIB Structure Chapter Front Panel RedundancyContents Introduction Using the EMM-E6 User’s GuideUsing the EMM-E6 User’s Guide UPS What’s not in the EMM-E6 User’s GuideConventions Window Conventions Screen DisplaysButton Using the MouseGetting Help Year 2000 Compliance EMM-E6 FirmwareUsing the Hub View Using the EMM-E6 Hub ViewHub View Front Panel Navigating Through the Hub ViewDevice Location UptimeDate and Time Device NameUsing the EMM-E6 Hub View EMM-E6 Ports Display Brim Ports Using the Mouse in a Hub View ModulePort Display Form Hub View Port Color CodesMonitoring Hub Performance Port Display Form Collisions ErrorsLoad TrafficPort Type ProtocolsFrame Sizes Using the EMM-E6 Hub View Contact Checking Device Status and Updating Front Panel InfoName and Location Chassis Type Checking Network StatusActive Users NameModule Type Checking Module StatusLink Status Checking Port StatusMedia Type StatusTopology Type Viewing the IP Address TableChecking Statistics Launching the Global Find MAC Address ToolUsing the EMM-E6 Hub View Broadcast Packets Received BytesTotal Packets Avg Packet SizeOOW Collisions Total ErrorsAlignment Errors CRC ErrorsGiant Frames Runt FramesProtocols/Frames Statistics Viewing the Port Source Address ListUsing the EMM-E6 Hub View Managing the Hub Setting the Polling IntervalsDevice General Status Contact StatusStatistics Configuring FNB ConnectionsDevice Configuration Port Operational StateConfiguring RIC MIM Connections To configure FNB connectivity for an individual port 15. Tpxmim Channel Selection Window Setting a Port’s Trunk TypeTo change a port’s topology status Enabling/Disabling MIM Ports Alarm Configuration From the Hub View Using Alarm ConfigurationFrom the command line stand-alone mode From the iconCRC Configuring AlarmsBroadcast Setting Repeater AlarmsSet Repeater Alarms Window Setting and Changing AlarmsSetting Module Alarms Setting Module and Port AlarmsSet the Status to Enabled Set Module Alarms WindowSet Port Alarms Window Setting Port AlarmsSet the Status to Enabled Alarm Configuration Setting Module and Port Alarms Link/Seg Traps What is a Segmentation Trap?Enabling and Disabling Link/Seg Traps What is a Link Trap?Spmarun r4hwtr IP address community name Viewing and Configuring Link/Seg Traps for Hub Modules Configuring Link/Seg Traps for the RepeaterModule Traps Window Port Traps Window Viewing and Configuring Link/Seg Traps for PortsLink/Seg Traps Link/Seg Traps Enabling and Disabling Link/Seg Traps Repeater Redundancy Setting Network Circuit RedundancySpmarun r4red IP address community name Configuring a Redundant CircuitChannel X Redundancy Window Add Circuit Address Window Repeater Redundancy To set the Poll Interval Monitoring RedundancyDisplaying the Source Address List Source AddressingDisplaying the Source Address List Source Addressing Setting the Aging Time Setting the Hash TypeLocking Source Addresses Source Address Locking on Older Devices Configuring Source Address Traps Repeater-level Traps Module- and Port-level Traps Source Addressing Port Source Address Traps Window Finding a Source AddressClick on to exit the window Security Spmarun r4sec IP address SU community name What is LANVIEWSECURE?Trunk port security New definitions for station and trunk portsSecure address assignment Full or partial security against eavesdropping Newest Lanviewsecure FeaturesContinuous learning mode Configurable violation responseForced non-secure status Learned addresses resetSecurity on Non-LANVIEWSECUREMIMs Configuring Security Security To assign secure addresses to a port Addresses Window Add MAC Address Window Boards with Multiple CachesTips for Successfully Implementing Eavesdropper Protection Resetting Learned AddressesEnabling Security and Traps Security Channel X Security Window Repeater-level Security and TrapsModule-level Security and Traps Channel X Module Security Window Channel X Port Security Window Port-level Security and TrapsSecurity Front Panel Redundancy Setting Front Panel RedundancySetting Front Panel Redundancy Add Circuit Address Window Front Panel Redundancy Setting Front Panel Redundancy EMM-E6 MIB Structure Ietf MIB SupportChassis MGR MIB ComponentsCtron Use Only Host ServicesIP Services Repeater One, Repeater Two, and Repeater ThreeRmon Host Rmon DefaultDistributed LAN Monitor MIB NavigatorBrief Word About MIB Components and Community Names EMM-E6 MIB Structure Index Index-2 Index-3 Index Index-4
Related manuals
Manual 64 pages 974 b