Cisco Systems 274, 474 manual Post Numeric Codes and Text Messages

Page 65

Chapter 5 Troubleshooting the System Hardware

Power-On Self Test (POST)

Note A single problem might cause several error messages. When this situation occurs, you should correct the cause of the first error message. After you correct the cause of the first error message, the other error messages usually will not occur the next time that you run the test.

POST Numeric Codes and Text Messages

This section covers POST errors that have numeric codes associated with them. The section also includes some text messages that may be encountered during POST.

 

 

Note

The computer will beep once after a POST text message is displayed on the

 

 

 

screen.

 

 

 

 

 

 

 

Table 5-10

Diagnostic Front Panel LEDs and Beep Codes

 

 

 

 

 

Control Panel Message

 

Description

 

 

 

 

101-Option ROM Checksum Error

System ROM or expansion board option ROM

 

 

 

 

checksum.

 

 

 

 

103-System Board Failure

DMA or timers.

 

 

 

 

110-Out of Memory Space for Option ROMs

Recently added PCI expansion card contains an

 

 

 

 

option ROM too large to download during POST.

 

 

 

 

162-System Options Not Set

Configuration incorrect.

 

 

 

 

RTC (real-time clock) battery may need to be

 

 

 

 

replaced.

 

 

 

 

163-Time & Date Not Set

Invalid time or date in configuration memory.

 

 

 

 

The RTC (real-time clock) battery may need to be

 

 

 

 

replaced.

 

 

 

 

163-Time & Date Not Set

CMOS jumper may not be properly installed.

 

 

 

 

164-Memory Size Error

Memory amount has changed since the last boot

 

 

 

 

(memory added or removed).

 

 

 

 

164-Memory Size Error

Memory configuration incorrect.

 

 

 

 

 

 

 

 

 

 

Cisco Wide Area Virtualization Engine 274 and 474 Hardware Installation Guide

 

 

 

 

 

 

 

OL-17739-01

 

 

 

 

5-13

 

 

 

 

 

Image 65
Contents November Page Page Page N T E N T S Wave Inline Network Adapter Altitude Viii Purpose PrefaceChapter Title Description AudienceOrganization Convention Description ConventionsXii Xiii Xiv Preface Xvi Xvii Xviii Related DocumentationXix OL-17739-01 Supported Products Introducing the Cisco Wide Area Virtualization EngineFront Panel Controls and LEDs Hardware FeaturesColor State Description Location of Ports and ConnectorsBack Panel LEDs and Connectors Ethernet Port Connector Console Port Serial Connector Safety Warnings Preparing to Install the Wide Area Virtualization EngineOL-17739-01 OL-17739-01 General Precautions Safety GuidelinesOL-17739-01 System Reliability Considerations Protecting Against Electrostatic Discharge OL-17739-01 Installing the Wide Area Virtualization Engine Installing the Wave Appliance on a Wall Installing the Wave Appliance on a TabletopWAVE-274 and WAVE-474 Appliance Mounting Sleeve Attaching the Mounting Sleeve Rack-Mounting Considerations Installing the Wave Appliance in an Equipment RackRack Requirements Connecting CablesConnecting Power and Booting the System Removing or Replacing a Wave Appliance Checking the LEDsOL-17739-01 Inline Network Adapter Description Wave Inline Network AdapterOL-17739-01 LEDs State Description Ports and LED IndicatorsConnection Required Cable Inline Network Adapter Cabling RequirementsConnection Required Cable Cable Requirements for Wave Connections Using Fast Ethernet Wave Inline Network Adapter Mgmt WAN Cabling Between Two Inline WAVEs OL-17739-01 Troubleshooting the System Hardware Identifying System Problems Checking Connections and Switches Network Connection Problems Troubleshooting the Ethernet ControllerEthernet Controller Problem Actions Ethernet Controller Troubleshooting ChartUndetermined Problems Problem-Solving Tips Symptoms and Solutions Symptom Cause and Action See the Undetermined Problems section on Symptom FRU or Action Post Overview Power-On Self Test PostPost Numeric Codes and Text Messages Control Panel Message Description Power-On Self Test Post Interpreting Post Diagnostic Front Panel LEDs and Beep Codes Post Diagnostic Front Panel LEDs and Beep Codes OL-17739-01 Post Diagnostic Front Panel LEDs and Beep Codes OL-17739-01 Specification Description Appliance SpecificationsA-4 Specification Description Inline Adapter Specifications Maintaining Your Site Environment Maintaining the Wide Area Virtualization EngineTemperature Altitude HumidityElectrostatic Discharge Dust and ParticlesCorrosion Magnetism Electromagnetic and Radio Frequency InterferenceShock and Vibration Power Source InterruptionsSurge Protectors Using Power Protection DevicesLine Conditioners Uninterruptible Power SuppliesD E IN-2 IN-3 IN-4