Cisco Systems 274, 474 manual Connection Required Cable

Page 47

Chapter 4 WAVE Inline Network Adapter

Inline Network Adapter Cabling Requirements

Table 4-2 Cable Requirements for WAVE Connections Using Gigabit

Ethernet (continued)

Connection

Required Cable

 

 

Router to WAVE and

Crossover or straight-through

 

 

WAVE to Router

Crossover or straight-through

 

 

WAVE to WAVE

Crossover or straight-through

 

 

Some switches support automatic medium-dependent interface crossover (MDIX). You can configure MDIX by using the mdix auto global configuration switch command. If your switch supports MDIX, you do not need to follow these cabling rules because MDIX automatically adjusts transmit and receive pairs when an incorrect cable type (crossover or straight-through) is installed on a 10/100 Fast Ethernet port. However, when you configure MDIX, you must also configure the port to use autosense (not manual selection of speed/duplex).

Caution If you are connecting to Fast Ethernet ports on both the LAN and the WAN sides of the WAVE inline appliance, you must consider the types of devices that are being connected, and you must use the correct cables. You must follow these cabling instructions for the inline network adapter to work properly. (See Table 4-3. For illustrations and examples, see the “Installation Scenarios and Cabling Examples for Fast Ethernet Connections” section on page 4-7.)

To connect the inline network adapter using the correct cables for Fast Ethernet connections, follow these steps:

Step 1 Determine the type of cable that you would use for a direct connection between your two end devices (without a WAVE inline network appliance connected between them) by using the following standard cabling rules:

•When you are directly connecting two network devices that are similar, such as two switches, use a crossover cable.

•When you are directly connecting two network devices that are different, such as a switch and router, use a straight-through cable.

 

 

Cisco Wide Area Virtualization Engine 274 and 474 Hardware Installation Guide

 

 

 

 

 

 

OL-17739-01

 

 

4-5

 

 

 

Page 46 Page 48
Image 47
Page 46 Page 48
Contents November Page Page Page N T E N T S Wave Inline Network Adapter Altitude Viii Purpose PrefaceChapter Title Description AudienceOrganization Convention Description ConventionsXii Xiii Xiv Preface Xvi Xvii Xviii Related DocumentationXix OL-17739-01 Supported Products Introducing the Cisco Wide Area Virtualization EngineFront Panel Controls and LEDs Hardware FeaturesColor State Description Location of Ports and ConnectorsBack Panel LEDs and Connectors Ethernet Port Connector Console Port Serial Connector Safety Warnings Preparing to Install the Wide Area Virtualization EngineOL-17739-01 OL-17739-01 General Precautions Safety GuidelinesOL-17739-01 System Reliability Considerations Protecting Against Electrostatic Discharge OL-17739-01 Installing the Wide Area Virtualization Engine Installing the Wave Appliance on a Wall Installing the Wave Appliance on a TabletopWAVE-274 and WAVE-474 Appliance Mounting Sleeve Attaching the Mounting Sleeve Rack-Mounting Considerations Installing the Wave Appliance in an Equipment RackRack Requirements Connecting CablesConnecting Power and Booting the System Removing or Replacing a Wave Appliance Checking the LEDsOL-17739-01 Inline Network Adapter Description Wave Inline Network AdapterOL-17739-01 LEDs State Description Ports and LED IndicatorsConnection Required Cable Inline Network Adapter Cabling RequirementsConnection Required Cable Cable Requirements for Wave Connections Using Fast Ethernet Wave Inline Network Adapter Mgmt WAN Cabling Between Two Inline WAVEs OL-17739-01 Troubleshooting the System Hardware Identifying System Problems Checking Connections and Switches Network Connection Problems Troubleshooting the Ethernet ControllerEthernet Controller Problem Actions Ethernet Controller Troubleshooting ChartUndetermined Problems Problem-Solving Tips Symptoms and Solutions Symptom Cause and Action See the Undetermined Problems section on Symptom FRU or Action Post Overview Power-On Self Test PostPost Numeric Codes and Text Messages Control Panel Message Description Power-On Self Test Post Interpreting Post Diagnostic Front Panel LEDs and Beep Codes Post Diagnostic Front Panel LEDs and Beep Codes OL-17739-01 Post Diagnostic Front Panel LEDs and Beep Codes OL-17739-01 Specification Description Appliance SpecificationsA-4 Specification Description Inline Adapter Specifications Maintaining Your Site Environment Maintaining the Wide Area Virtualization EngineTemperature Altitude HumidityElectrostatic Discharge Dust and ParticlesCorrosion Magnetism Electromagnetic and Radio Frequency InterferenceShock and Vibration Power Source InterruptionsSurge Protectors Using Power Protection DevicesLine Conditioners Uninterruptible Power SuppliesD E IN-2 IN-3 IN-4
Top Page Image Contents