Cisco Systems 274, 474 manual IN-3

Page 87

Index

description 1-3,1-5front panel (table) 1-3front view 1-2

inline network adapter 4-3rear view 1-4

line conditioners using B-8

M

magnetism

preventing effects of B-5maintenance B-1 to B-7memory

problems 5-10

microprocessor

problems 5-11

N

network

connection problems 5-4removing WAVE from 3-7

POST description 5-12error codes 5-12

power

connecting to system 3-6power on LED 1-3power-on self-test

See POST

power source interruptions preventing damage from B-6

power supplies

using uninterruptible B-8problem solving

overview 5-1tips 5-7

R

rack requirements 3-6radio frequency interference

See RFI

removing or replacing WAVE 3-7

RFI

preventing effects of B-5

P

ports			S
ports
	console (serial) 1-6		safety
	inline network adapter	4-3	general precautions 2-4
		Cisco Wide Area Virtualization Engine 274 and 474 Hardware Installation Guide

	OL-17739-01				IN-3
	OL-17739-01				IN-3

Image 87

Contents November Page Page Page N T E N T S Wave Inline Network Adapter Altitude Viii Purpose PrefaceAudience OrganizationChapter Title Description Convention Description ConventionsXii Xiii Xiv Preface Xvi Xvii Xviii Related DocumentationXix OL-17739-01 Supported Products Introducing the Cisco Wide Area Virtualization EngineFront Panel Controls and LEDs Hardware FeaturesColor State Description Location of Ports and ConnectorsBack Panel LEDs and Connectors Ethernet Port Connector Console Port Serial Connector Safety Warnings Preparing to Install the Wide Area Virtualization EngineOL-17739-01 OL-17739-01 General Precautions Safety GuidelinesOL-17739-01 System Reliability Considerations Protecting Against Electrostatic Discharge OL-17739-01 Installing the Wide Area Virtualization Engine Installing the Wave Appliance on a Wall Installing the Wave Appliance on a TabletopWAVE-274 and WAVE-474 Appliance Mounting Sleeve Attaching the Mounting Sleeve Rack-Mounting Considerations Installing the Wave Appliance in an Equipment RackConnecting Cables Connecting Power and Booting the SystemRack Requirements Removing or Replacing a Wave Appliance Checking the LEDsOL-17739-01 Inline Network Adapter Description Wave Inline Network AdapterOL-17739-01 LEDs State Description Ports and LED IndicatorsConnection Required Cable Inline Network Adapter Cabling RequirementsConnection Required Cable Cable Requirements for Wave Connections Using Fast Ethernet Wave Inline Network Adapter Mgmt WAN Cabling Between Two Inline WAVEs OL-17739-01 Troubleshooting the System Hardware Identifying System Problems Checking Connections and Switches Network Connection Problems Troubleshooting the Ethernet ControllerEthernet Controller Problem Actions Ethernet Controller Troubleshooting ChartUndetermined Problems Problem-Solving Tips Symptoms and Solutions Symptom Cause and Action See the Undetermined Problems section on Symptom FRU or Action Post Overview Power-On Self Test PostPost Numeric Codes and Text Messages Control Panel Message Description Power-On Self Test Post Interpreting Post Diagnostic Front Panel LEDs and Beep Codes Post Diagnostic Front Panel LEDs and Beep Codes OL-17739-01 Post Diagnostic Front Panel LEDs and Beep Codes OL-17739-01 Specification Description Appliance SpecificationsA-4 Specification Description Inline Adapter Specifications Maintaining Your Site Environment Maintaining the Wide Area Virtualization EngineTemperature Altitude HumidityDust and Particles CorrosionElectrostatic Discharge Magnetism Electromagnetic and Radio Frequency InterferenceShock and Vibration Power Source InterruptionsSurge Protectors Using Power Protection DevicesLine Conditioners Uninterruptible Power SuppliesD E IN-2 IN-3 IN-4