Cisco Systems Cisco ASR 1006 quick start Connect the Router to the Network

Page 13

Step 8 Connect the opposite end of the grounding wire to the appropriate grounding point at your site to ensure an adequate chassis ground.

This completes the procedure for attaching a chassis ground connection. Go to the “Connect the Router to the Network” section on page 13 for information on attaching cables.

4Connect the Router to the Network

This section provides information about cables and ports and attaching the router to the network.

•Console and Auxiliary Port Cable Connections, page 13

•Management Ethernet Port Cable Connection, page 13

•Connect the Shared Port Adapter Cables, page 14

•Install the Cables in the Cable-Management Bracket, page 15

Console and Auxiliary Port Cable Connections

This section describes how to attach a cable to the console or auxiliary ports on the Cisco ASR 1006 Router. The Cisco ASR 1006 Router uses RJ-45 ports for both the auxiliary port and console port to attach a modem or console terminal.

The console DCE-mode port connects a console terminal and a DTE-mode auxiliary port connects a modem or other DCE device to your router.

Note Both the console and the auxiliary ports are asynchronous serial ports; any devices connected to these ports must be capable of asynchronous transmission. (Asynchronous is the most common type of serial device; for example, most modems are asynchronous devices.)

Step 1 Before connecting a terminal to the console port, configure the terminal to match the router console port as follows: 9600 baud, 8 data bits, no parity, 1 stop bits. See Figure 8 for console and auxiliary port connector location.

Step 2 After you establish normal router operation, you can disconnect the terminal.

Note For console and auxiliary port pinouts, see Appendix A, Cisco ASR 1000 Series routers Specifications, in the Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide.

Management Ethernet Port Cable Connection

Before you can use the console interface on the router using a terminal or PC, you must perform the following steps:

Step 1 Configure your terminal emulation software with the following settings: 9600 bits per second (bps), 8 data bits, No parity, one stop bit, No flow control.

Note For information about how to change the default settings to meet the requirements of your terminal or host, refer to the Cisco IOS Terminal Services Configuration Guide.

Step 2 Connect a terminal or PC to the console port using the cable and adapters provided in the accessory kit that shipped with your Cisco ASR 1006 Router:

–Place the console port mode switch in the in position (factory default).

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Cisco ASR 1006 Router Document Revision History Documentation and ResourcesPrepare for Equipment Shelf or Tabletop Installation Prepare for InstallationSite Preparation and Unpacking Tools and PartsRack-Mount the Router Prepare for Rack-Mount InstallationAttach the Rack-Mount Brackets-Chassis Front-Mounted Insert and tighten the black screws on one side Attach the Rack-Mount Brackets-Chassis Rear Rack-MountedCisco ASR 1006 Router Rear Rack-Mounting Four-Post Rack InstallationInstalling the Cisco ASR 1006 Router in a Four-Post Rack Two-Post Rack Installation Installing the Cisco ASR 1006 Router in a Two-Post Rack Attach the Cable-Management Bracket 280036 Attaching a Grounding Lug to the Chassis Ground Connector Chassis Ground Connection InstallationConsole and Auxiliary Port Cable Connections Connect the Router to the NetworkManagement Ethernet Port Cable Connection Connect the Shared Port Adapter Cables Management Ethernet Port ConnectorsConnecting AC-Input Power to the Cisco ASR 1006 Router Install the Cables in the Cable-Management BracketStart the System Plug the power cable into the inlet Connect DC Power to the Cisco ASR 1006 RouterUnit. Statement Installing the Cisco ASR 1006 Router DC Ground Lugs Wiring the DC-Input Power Source DC Power Supply Terminal Block 280024 280311 DC Power Supply Terminal Block and Plastic Cover Verifying Power Supply OperationFollowing output displays Start the SystemActv Validatepackage SHA-1 hash Page Etherport Page Using the Console Interface Configure the RouterConfigure Global Parameters Using the Setup Facility OK? No clns routing Tftptimeout Page Save the Running Configuration to Nvram Check the Running Configuration SettingsPerform Other Configuration Tasks Power Off the Cisco ASR 1006 Router After InstallationRemove and Then Replace an AC Power Supply Replace a Power Supply in a Cisco ASR 1006 RouterRemove the DC Power Supply Unit Might One All Replace the DC Power Supply Install and Remove the Shared Port AdapterHandling a SPA Page USA
Top Page Image Contents