Cisco Systems Cisco ASR 1006 quick start Check the Running Configuration Settings

Page 35

Note Basic management setup configures enough connectivity for managing the system; extended setup will ask you to configure each interface on the system. For detailed information about setting global parameters, refer to the Cisco ASR 1000_Series Aggregation Services Routers Software Configuration Guide.

Check the Running Configuration Settings

To check the value of the settings you have entered, enter the show running-configcommand at the Router# prompt:

Router# show running-config

To review changes you make to the configuration, use the EXEC mode show startup-configcommand to see the changes in

NVRAM.

Save the Running Configuration to NVRAM

To store the configuration or changes to your startup configuration in NVRAM, use the copy running-configstartup-configcommand to save your configuration changes to the startup configuration so that the changes will not be lost if the software reloads or a power outage occurs. For example:

Router# copy running-config startup-config

Building configuration...

It might take a minute or two to save the configuration. After the configuration has been saved, the following output appears:

[OK]

Router#

On most platforms, this task saves the configuration to NVRAM. On the Class A Flash file system platforms, this task saves the configuration to the location specified by the CONFIG_FILE environment variable. The CONFIG_FILE variable defaults to

NVRAM.

To review changes you make to the configuration, use the EXEC mode show startup-configcommand to see the changes.

Note Using the copy running-configstartup-configcommand saves the configuration settings that you created in the router using configuration mode and the setup facility. If you fail to do this, your configuration will be lost the next time you reload the router.

Perform Other Configuration Tasks

To make advanced configuration changes after you establish the basic startup configuration for your router, refer to the Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide and modular configuration and modular command reference publications in the Cisco IOS software configuration documentation set that corresponds to the software release installed on your Cisco hardware. These publications contain additional information on using the configure command. The configuration publications also provide information about the following tasks:

•Understanding Diagnostic Mode feature

•Understanding Command Modes

•Booting and rebooting the router

•Understanding software packages for the Cisco ASR 1000 Series Aggregation Services Routers

•Software Upgrades

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Cisco ASR 1006 Router Document Revision History Documentation and ResourcesTools and Parts Prepare for InstallationPrepare for Equipment Shelf or Tabletop Installation Site Preparation and UnpackingAttach the Rack-Mount Brackets-Chassis Front-Mounted Prepare for Rack-Mount InstallationRack-Mount the Router Insert and tighten the black screws on one side Attach the Rack-Mount Brackets-Chassis Rear Rack-MountedCisco ASR 1006 Router Rear Rack-Mounting Four-Post Rack InstallationInstalling the Cisco ASR 1006 Router in a Four-Post Rack Two-Post Rack Installation Installing the Cisco ASR 1006 Router in a Two-Post Rack Attach the Cable-Management Bracket 280036 Attaching a Grounding Lug to the Chassis Ground Connector Chassis Ground Connection InstallationManagement Ethernet Port Cable Connection Connect the Router to the NetworkConsole and Auxiliary Port Cable Connections Connect the Shared Port Adapter Cables Management Ethernet Port ConnectorsStart the System Install the Cables in the Cable-Management BracketConnecting AC-Input Power to the Cisco ASR 1006 Router Plug the power cable into the inlet Connect DC Power to the Cisco ASR 1006 RouterUnit. Statement Installing the Cisco ASR 1006 Router DC Ground Lugs Wiring the DC-Input Power Source DC Power Supply Terminal Block 280024 280311 DC Power Supply Terminal Block and Plastic Cover Verifying Power Supply OperationFollowing output displays Start the SystemActv Validatepackage SHA-1 hash Page Etherport Page Configure Global Parameters Using the Setup Facility Configure the RouterUsing the Console Interface OK? No clns routing Tftptimeout Page Perform Other Configuration Tasks Check the Running Configuration SettingsSave the Running Configuration to Nvram Power Off the Cisco ASR 1006 Router After InstallationRemove and Then Replace an AC Power Supply Replace a Power Supply in a Cisco ASR 1006 RouterRemove the DC Power Supply Unit Might One All Replace the DC Power Supply Install and Remove the Shared Port AdapterHandling a SPA Page USA
Top Page Image Contents