Cisco Systems Cisco ASR 1006 quick start Configure the Router, Using the Console Interface

Page 30

Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVIPSERVICESK9-M), Experimental Version 12.2(20080110:152728) [BLD-mcp_dev.MCP_CRYPTO_INCREMENTAL_BLD_20080110 103]

Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Thu 10-Jan-08 07:29 by mcpre

*Feb 13 12:49:01.253: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF Router>

During the boot process, observe the system LEDs. The LEDs on the shared port adapter go on and off in irregular sequence. They may go on, go out, and go on again for a short time. On the router, the green STATUS LED comes on and stays on. For software configuration information, see the Cisco ASR 1000 Series Aggregation Services Software Configuration Guide.

6Configure the Router

Using the Console Interface

To access the command-line interface using the console, follow these steps:

Step 1 Once the terminal console port is connected, configure your terminal emulation software with valid settings. Start at the following prompt:

Press Return for Console prompt

Step 2 Press Return to enter user EXEC configuration mode. The following prompt appears:

Router>

Step 3 From user EXEC configuration mode, enter the enable command as shown in the following example:

Router> enable

Step 4 At the password prompt, enter your system’s password. If an enable password has not been set on your system, this step may be skipped. The following example shows entry of the password called enablepass:

Password: enablepass

Step 5 When your enable password is accepted, the privileged EXEC configuration mode prompt appears:

Router#

Step 6 You now have access to the CLI in privileged EXEC configuration mode and you can enter the necessary commands to complete your desired tasks.

Step 7 To exit the console session, enter the quit command as shown in the following example:

Router# quit

Configure Global Parameters Using the Setup Facility

When you first start the setup program, you must configure the global parameters. These parameters are used for controlling system-wide settings. Complete the following steps to enter the global parameters:

Step 1 Connect a console terminal to the console port and then boot the router. The system boots from flash memory. The following information appears after about 30 seconds. This is only an example of the output display; prompts may vary.

Step 2 The first sections of the configuration script appear only at an initial system startup. On subsequent uses of the setup facility, the script begins with a System Configuration Dialog as shown below: When asked if you would like to enter the initial configuration dialog, enter yes.

Would you like to enter the initial configuration dialog? [yes/no] yes

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

30

Image 30
Contents Cisco ASR 1006 Router Documentation and Resources Document Revision HistorySite Preparation and Unpacking Prepare for InstallationPrepare for Equipment Shelf or Tabletop Installation Tools and PartsPrepare for Rack-Mount Installation Rack-Mount the RouterAttach the Rack-Mount Brackets-Chassis Front-Mounted Attach the Rack-Mount Brackets-Chassis Rear Rack-Mounted Insert and tighten the black screws on one sideFour-Post Rack Installation Cisco ASR 1006 Router Rear Rack-MountingInstalling the Cisco ASR 1006 Router in a Four-Post Rack Two-Post Rack Installation Installing the Cisco ASR 1006 Router in a Two-Post Rack Attach the Cable-Management Bracket 280036 Chassis Ground Connection Installation Attaching a Grounding Lug to the Chassis Ground ConnectorConnect the Router to the Network Console and Auxiliary Port Cable ConnectionsManagement Ethernet Port Cable Connection Management Ethernet Port Connectors Connect the Shared Port Adapter CablesInstall the Cables in the Cable-Management Bracket Connecting AC-Input Power to the Cisco ASR 1006 RouterStart the System Connect DC Power to the Cisco ASR 1006 Router Plug the power cable into the inletUnit. Statement Installing the Cisco ASR 1006 Router DC Ground Lugs Wiring the DC-Input Power Source DC Power Supply Terminal Block 280024 280311 Verifying Power Supply Operation DC Power Supply Terminal Block and Plastic CoverStart the System Following output displaysActv Validatepackage SHA-1 hash Page Etherport Page Configure the Router Using the Console InterfaceConfigure Global Parameters Using the Setup Facility OK? No clns routing Tftptimeout Page Check the Running Configuration Settings Save the Running Configuration to NvramPerform Other Configuration Tasks After Installation Power Off the Cisco ASR 1006 RouterReplace a Power Supply in a Cisco ASR 1006 Router Remove and Then Replace an AC Power SupplyRemove the DC Power Supply Unit Might One All Install and Remove the Shared Port Adapter Replace the DC Power SupplyHandling a SPA Page USA