Cisco Systems Cisco ASR 1006 quick start Tftptimeout

Page 33

!

interface GigabitEthernet0 shutdown

no ip address

dialer-list 1 protocol ip permit dialer-list 1 protocol ipx permit

!

end

[0]Go to the IOS command prompt without saving this config.

[1]Return back to the setup without saving this config.

[2]Save this configuration to nvram and exit.

Enter your selection [2]:

Router#reload

Proceed with reload? [confirm]

*Jan 11 06:59:29.476: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload command.

System Bootstrap, Version 12.2(20071105:235056) [gschnorr-mcp_rommon_rel_1_25 101], DEVELOPMENT SOFTWARE Copyright (c) 1994-2007 by cisco Systems, Inc.

Compiled Mon 05-Nov-07 16:50 by gschnorr-mcp_rommon_rel_1_25

Current image running: Boot ROM1

Last reset cause: LocalSoft

SATA drive PCI config error

ASR1006-RP1 platform with 2097152 Kbytes of main memory

rommon 1 > b tftp:images/packages_crypto/asr1000rp1-advipservicesk9.mcp_dev_20080109_101550.bin

IP_ADDRESS: 2.1.6.5

IP_SUBNET_MASK: 255.255.0.0 DEFAULT_GATEWAY: 2.1.0.1

TFTP_SERVER: 2.0.0.2

TFTP_FILE: images/packages_crypto/asr1000rp1-advipservicesk9.mcp_dev_20080109_101550.bin Using midplane macaddr

TFTP_MACADDR: 00:14:a8:ff:42:ff

TFTP_VERBOSE: Progress TFTP_RETRY_COUNT: 18

TFTP_TIMEOUT: 7200

TFTP_CHECKSUM: Yes

ETHER_PORT: 3 ETHER_SPEED_MODE: Auto Detect

link up 1000Mbps/FD.......

Receiving images/packages_crypto/asr1000rp1-advipservicesk9.mcp_dev_20080109_101550.bin from 2.0.0.2

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!

File reception completed.

Boot image size = 206741708 (0xc52a0cc) bytes

Using midplane macaddr

Package header rev 0 structure detected Calculating SHA-1 hash...done validate_package: SHA-1 hash:

calculated a8301e1e:17821e94:07654c49:4ca6fe49:518af2c2 expected a8301e1e:17821e94:07654c49:4ca6fe49:518af2c2

Image validated

33

Image 33

Contents Cisco ASR 1006 Router Document Revision History Documentation and ResourcesPrepare for Equipment Shelf or Tabletop Installation Prepare for InstallationSite Preparation and Unpacking Tools and PartsPrepare for Rack-Mount Installation Rack-Mount the RouterAttach the Rack-Mount Brackets-Chassis Front-Mounted Insert and tighten the black screws on one side Attach the Rack-Mount Brackets-Chassis Rear Rack-MountedCisco ASR 1006 Router Rear Rack-Mounting Four-Post Rack InstallationInstalling the Cisco ASR 1006 Router in a Four-Post Rack Two-Post Rack Installation Installing the Cisco ASR 1006 Router in a Two-Post Rack Attach the Cable-Management Bracket 280036 Attaching a Grounding Lug to the Chassis Ground Connector Chassis Ground Connection InstallationConnect the Router to the Network Console and Auxiliary Port Cable ConnectionsManagement Ethernet Port Cable Connection Connect the Shared Port Adapter Cables Management Ethernet Port ConnectorsInstall the Cables in the Cable-Management Bracket Connecting AC-Input Power to the Cisco ASR 1006 RouterStart the System Plug the power cable into the inlet Connect DC Power to the Cisco ASR 1006 RouterUnit. Statement Installing the Cisco ASR 1006 Router DC Ground Lugs Wiring the DC-Input Power Source DC Power Supply Terminal Block 280024 280311 DC Power Supply Terminal Block and Plastic Cover Verifying Power Supply OperationFollowing output displays Start the SystemActv Validatepackage SHA-1 hash Page Etherport Page Configure the Router Using the Console InterfaceConfigure Global Parameters Using the Setup Facility OK? No clns routing Tftptimeout Page Check the Running Configuration Settings Save the Running Configuration to NvramPerform Other Configuration Tasks Power Off the Cisco ASR 1006 Router After InstallationRemove and Then Replace an AC Power Supply Replace a Power Supply in a Cisco ASR 1006 RouterRemove the DC Power Supply Unit Might One All Replace the DC Power Supply Install and Remove the Shared Port AdapterHandling a SPA Page USA