Cabletron Systems manual ESX-1320/ESX-1380 Installation Guide

Page 3

Only qualified personnel should perform installation procedures.

NOTICE

Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.

The hardware, firmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

Copyright 1996 by Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005 All Rights Reserved

Printed in the United States of America

Order Number: 9031574-03 November 1996

SecureFast Switch, SPECTRUM, LANVIEW, MicroMMAC, and BRIM are registered trademarks and Element Manager, EPIM, EPIM-A,EPIM-F1,EPIM-F2,EPIM-F3,EPIM-T,EPIM-X,ESX-1320,ESX-1380,FOT-F,FOT-F3,HubSTACK, SEH, SEHI, and TMS-3 are trademarks of Cabletron Systems, Inc.

All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.

WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Printed on

Recycled Paper

ESX-1320/ESX-1380 Installation Guide

i

Image 3
Contents Installation Guide Page ESX-1320/ESX-1380 Installation Guide DOC Notice Cabletron Software Program License Declaration of Conformity Contents Contents Chapter Introduction ESX-1320 and ESX-1380 SwitchesFeatures Using this ManualFeatures Following conventions are used throughout this document Document ConventionsGetting Help Related ManualsAnonymous Chapter Controls and Indicators Reset ButtonLanview LEDs Simplex or Full Duplex Mode Operation LCD DisplayNetwork Management Capabilities Simplex or Full Duplex Mode Operation ESX-1320/ESX-1380 Installation Guide Chapter Installation Unpacking the ESX Removing the Chassis Cover Screws Removing the Chassis Cover Setting Mode SwitchesESX Mode Switch Location/Component Layout Setting Mode Switches Nvram Reset Switch Nvram Reset SwitchSimm Upgrades Installing SIMMsLocating SIMMs Installing the Flash Simm Installing the Sdram or Ldram Simm Brim Connection Installing the ESXTabletop or Shelf Installation Tabletop or Shelf InstallationRackmount Installation Rack Mounting the ESX 12 Installing the ESX in the Rack Connecting to the Power SourcePRE-NETWORK Installation Test 13 Pre-Installation Test Connecting a Twisted Pair Segment to the ESX-1320 Connecting to the Network14 ESX-1320 Twisted Pair Connection 15 Cable Pinouts RJ45 Crossover Cable Connecting a 10BASE-F Segment to the ESX-138016 ST Connector Insertion Using Lanview Chapter TroubleshootingTroubleshooting Using Lanview Troubleshooting Checklist Troubleshooting Checklist Reset Button Using the Reset ButtonLCD Using the LCDUnsaved Initialization Messages From the last Static System message Static System MessagesStatic System Messages Displayed Messages Comments From the product name display Alarm MessagesDisplayed Messages Comments Saved System MessagesFrom an Alarm Message display Failure or Error Messages Appendix a Specifications FunctionalityCOM Port 1 and COM Port Physical Properties Electrical SpecificationsEnvironmental Requirements RegulatoryAppendix B Ethernet Cabling Requirements Network Requirements10BASE-T Twisted Pair Network Appendix B Ethernet Cabling Requirements Multimode Fiber Optic Network ESX-1320/ESX-1380 Installation Guide Numerics IndexIndex-2 ESX-1320/ESX-1380 Installation Guide ESX-1320/ESX-1380 Installation Guide Index-3 Index Index-4 ESX-1320/ESX-1380 Installation Guide Power Supply Cord