Cabletron Systems ESX-1320 manual Power Supply Cord

Page 65

POWER SUPPLY CORD

The mains cord used with this equipment must be a 2 conductor plus ground type with minimum 0.75 mm square conductors and must incorporate a standard IEC appliance coupler on one end and a mains plug on the other end which is suitable for the use and application of the product and that is approved for use in the country of application.

GERMAN:

Die Netzleitung, die mit diesem Geraet benuetzt wird, soll einen zwei Leiter mit Erdleiter haben, wobei die Leiter mindestens 0.75 mm sind, mit einer normalen IEC Geraetesteckdose an einem Ende und einem Geraetestecker am anderen Ende versehen sind, der fuer den Gebrauch und die Anwendung des Geraetes geeignet und der zum Benuetzen im Lande der Anwendung anerkannt ist.

SPANISH:

El cable principal de la red eléctrica utilizado con este equipo debe tener 2 conductores y 1 toma de tierra con un mínimo de 0.75 mm2 cada uno y necesita tener un aparato de acoplamiento standard IEC en un extremo y un enchufe para el cable principal de la red eléctrica en el otro extremo, lo cual sea adecuado para el uso y applicación del producto y lo cual sea aprobado para uso en el pais de applicación.

FRENCH:

Le cordon d' alimentation reliant cet appareil au secteur doit obligatoirement avoir deux fils conducteurs de 0.75 mm2 minimum et un fil de terre. It doit également être équipé du côté appareil d'une fiche agrée IEC et du côte secteur, d'une prise adaptée à l'usage du produit et aux normes du pays où l'appareil est utilisé.

Image 65
Contents Installation Guide Page ESX-1320/ESX-1380 Installation Guide DOC Notice Cabletron Software Program License Declaration of Conformity Contents Contents Chapter Introduction ESX-1320 and ESX-1380 SwitchesFeatures Using this ManualFeatures Following conventions are used throughout this document Document ConventionsGetting Help Related ManualsAnonymous Lanview LEDs Chapter Controls and IndicatorsReset Button Network Management Capabilities Simplex or Full Duplex Mode OperationLCD Display Simplex or Full Duplex Mode Operation ESX-1320/ESX-1380 Installation Guide Chapter Installation Unpacking the ESX Removing the Chassis Cover Screws Removing the Chassis Cover Setting Mode SwitchesESX Mode Switch Location/Component Layout Setting Mode Switches Nvram Reset Switch Nvram Reset SwitchLocating SIMMs Simm UpgradesInstalling SIMMs Installing the Flash Simm Installing the Sdram or Ldram Simm Brim Connection Installing the ESXTabletop or Shelf Installation Tabletop or Shelf InstallationRackmount Installation Rack Mounting the ESX 12 Installing the ESX in the Rack Connecting to the Power SourcePRE-NETWORK Installation Test 13 Pre-Installation Test Connecting a Twisted Pair Segment to the ESX-1320 Connecting to the Network14 ESX-1320 Twisted Pair Connection 15 Cable Pinouts RJ45 Crossover Cable Connecting a 10BASE-F Segment to the ESX-138016 ST Connector Insertion Using Lanview Chapter TroubleshootingTroubleshooting Using Lanview Troubleshooting Checklist Troubleshooting Checklist Reset Button Using the Reset ButtonLCD Using the LCDUnsaved Initialization Messages From the last Static System message Static System MessagesStatic System Messages Displayed Messages Comments From the product name display Alarm MessagesDisplayed Messages Comments Saved System MessagesFrom an Alarm Message display Failure or Error Messages COM Port 1 and COM Port Appendix a SpecificationsFunctionality Environmental Requirements Electrical SpecificationsRegulatory Physical Properties10BASE-T Twisted Pair Network Appendix B Ethernet Cabling RequirementsNetwork Requirements Appendix B Ethernet Cabling Requirements Multimode Fiber Optic Network ESX-1320/ESX-1380 Installation Guide Numerics IndexIndex-2 ESX-1320/ESX-1380 Installation Guide ESX-1320/ESX-1380 Installation Guide Index-3 Index Index-4 ESX-1320/ESX-1380 Installation Guide Power Supply Cord