Cabletron Systems 9A100 manual Server Is local Server Connection Established

Page 36

%•F"›amV˜"m˜,6˜p¦F•˜":1˜=/"2

˜˜,6˜3¦F•˜":1˜"m=˜/"2'

3.Enter the show client command to make sure the client is operational and to obtain the 20-byte ATM address of the ARP server. For instance, if you used the client number (client 1) from the example in step 2, enter the following command.

SmartSwitch # show client 1

IP/ATM Client 1

============================================================================

Client State

: Operational

Client Address

: 39:00:00:00:00:00:00:00:00:00:14:41:80:00:00:5A:01:01:01:00

Server

: is local

Server Connection : Established

MTU

: 9180

IP Address

: 90.1.1.1

IP NetMask

: 255.255.255.0

SmartSwitch #

 

4.Physically connect your end nodes and edge devices to the SmartSwitch 9A100 ports.

Note Your end nodes do not need to be physically attached to the switch that contains the ARP server. For example, an end station is connected to a SmartSwitch 9A100 switch that is connected through a route to the switch containing the ARP server. No special configuration is needed for this end station to participate in the VLAN because the end station automatically finds its path across the route to the ARP server and the other VLAN members.

5.Configure the ATM interface or adapter for end nodes and edge devices. Typically, configuration consists of designating IP over ATM as the protocol, assigning the device an IP address, and specifying the 20-byte ATM address of the ARP server (the switch’s client address). For details on the SmartSwitch 9A100 automatic addressing scheme for IP over ATM, see Section 3.1.1.

6.As your end devices are configured and started, they register with the ARP server. You can test whether your IP over ATM VLAN is functional by pinging from one end device to another.

To make certain that all end devices are registered with the ARP server, you can inspect the switch’s ARP table using the show ipatmarp command. For example, if three end devices with IP addresses 90.1.1.2, 90.1.1.3, and 90.1.1.4 are added to the VLAN, the following ARP table entries should exist:

SmartSwitch # show ipatmarp

ClientNumber(ALL)

:

IP/ATM Server 1 ARP Table

IP Address

ATM Address

============================================================================

90.1.1.239:00:00:00:00:00:00:00:00:00:14:41:80:00:00:5A:01:01:02:00 IP/ATM Server 3 ARP Table

IP Address ATM Address

============================================================================

90.1.1.339:00:00:00:00:00:00:00:00:00:14:41:80:00:00:5A:01:01:03:00 IP/ATM Server 5 ARP Table

IP Address ATM Address

============================================================================

90.1.1.439:00:00:00:00:00:00:00:00:00:14:41:80:00:00:5A:01:01:04:00 SmartSwitch #

3-2 SmartSwitch 9A100 User Guide

Image 36
Contents SmartSwitch 9A100 User Guide SmartSwitch 9A100 User Guide FCC Class a Notice Declaration of Conformity Addendum Safety Information Class 1 Laser Transceivers Fiber Optic Protective Caps Regulatory Compliance Summary Safety Revision History Table of Contents Specifications Acronyms Index Xii SmartSwitch 9A100 User Guide List of Figures List of Figures Xiv SmartSwitch 9A100 User Guide List of Tables List of Tables Xvi SmartSwitch 9A100 User Guide Introduction Introduction SmartSwitch 9A100 User Guide Switch Installation and Setup Unpacking the SwitchCheck Accessory Carton Contents Inspecting the Switch SmartSwitch 9A100-04 front panel1 DS3 and E3 I/O Module Configuration Installing the Switch Installing the SmartSwitch 9A100 Configuring the Switch SmartSwitch 9A100 console and network connections Using the Console Console CommandsSmartSwitch # show portconfig a1 SmartSwitch # set consoletimeout Console Time-outCreating an Alias TrafficAmbiguous Commands SwitchTrafficCongestion. For exampleSmartswitch ATM Administrator SmartSwitch # ? add laneclientConsole Help ExteriorSmartSwitch ATM Administrator Installation Steps MB RAMStarting SmartSwitch ATM Administrator the First Time Accessing Online HelpUser Name Access Level Default Password SmartSwitch ATM Administrator SmartSwitch # add ipatmclient IP Over ATM and LaneCreating AN IP Over ATM Vlan Server Is local Server Connection Established Creating AN Emulated LAN ATM Addressing for IP over ATM3900000000000000000014418000005A01010100 Add Elan No Lane server address is specified see note belowIlmi ELANs Across Multiple Switches ATM Addressing for LAN EmulationSwitch Clients SmartSwitch# add laneclientElan1 Page Switch Administration Backing UP and Restoring Switch ConfigurationPath /backdir/config-1 SmartSwitch# restore switch SmartSwitch # show netprefix b2ATM Routing Creating an Iisp RouteAtmAddress AtmrouteIisp route across Pnni domain UNI Routes Route Metrics SmartSwitch # show pnnimetrics IP Routing90.1.1.254 Route NET TableEvents and Alarms Event CategoriesViewing Events and Alarms SmartSwitch # set eventdisplayDeleting Events and Alarms SmartSwitch # set alarmdisplayPVC Connections SmartSwitch # add trafficdescriptor SmartSwitch # show trafficdescriptorPoint-to-Point PVCs 100Point-to-Multipoint PVCs Md1 #add trafficdescriptorConnecting to Local Switch Client Through a PVC Local10.1.1.0 Non-zero VPIs VCC Mask Index VPI Bits VPI Values VCI Bits VCI ValuesUse show portconfig to see the change to port A1 SmartSwitch # set portconfig a1Traffic Management Traffic DescriptorsType Number Descriptor Characteristics Traffic Descriptor with CLP and best effortCall Admission Control Policy 80005000 Ubr SmartSwitch # set porttrafficcongestion Min for CBR queueQoS Queue Recommended Settings SmartSwitch # show switchtrafficcongestionEFCI, EPD, and RM Thresholds Accessing the Boot Load Prompt Upgrading and Changing SoftwareBoot Load Commands Command Action ParametersUpgrading Boot Load Software Boot PromFlash RAM =df b Upgrading Post Diagnostic Software =chpi=df p Upgrading Switch Operating Software =df sUsing the Update Firmware Command SmartSwitch # update firmware214.95.77.240 Saving Core Dumps Tftpboot/bobr/core Set CoreDump command204.95.77.240 BobrError IP e0103288 PFP e04be080 R0pfp e04be040 R1sp e04be0c0 Troubleshooting Troubleshooting IP Over ATMTroubleshooting LAN Emulation Troubleshooting Pnni Links Troubleshooting Congestion Diagnosing CongestionGlobal Congestion Port Congestion Troubleshooting Congestion Appendix a Specifications FunctionFigure A-1 SmartSwitch 9A100 front panel Specification Value ¢ %+2,%/˜96%,,%,329Table A-4 ATM port specifications Protocol StandardManagement Protocol Supported MIBs RJ-45 Pin RJ-45 Color DB-9 Pin DB-9 DescriptionTechnical Specifications Appendix B Agent Support MIB, SMI, MIB Files and Internet MIB HierarchyZeitNet Cabletron Proprietary MIBs MIB, SMI, MIB Files and Internet MIB HierarchyRelation Between Object Identifier and the Represented Value Supported protocols Supported SMI FormatsZeitnet Cabletron Proprietary MIB Groups Name Object Identifier FunctionSmartSwitch 9A100 MIB Support MIB ExceptionsManaging the SmartSwitch 9A100 Console Commands that Affect the Agent Update firmware Backup Restore RebootFAX Service Electronic ServicesAppendix C Technical Support Telephone AssistanceHardware Warranty Software WarrantyRepair Services Appendix D Acronyms Bootp DTE FCS Ilmi LES Netbeui PDU RMA SVC VBR/RT Acronyms SmartSwitch 9A100 User Guide Index NumericsElan Lane Snmp Lane Pnni Non-zero values