Extron electronic CrossPoint 124 Operationeration, cont’d, Front Panel Controls and Indicators

Page 22

Operationeration, cont’d

Front Panel Controls and Indicators

The front panel controls (figure 3-1 and figure 3-2) are grouped into two sets. The input and output buttons and LED indicators are grouped on the left side of the control panel. The control buttons and input/output (I/O) selection buttons and indicators are grouped on the right side of the panel.

While the number of inputs and outputs varies depending on the size of the matrix, there are only two front panel arrangements. The CrossPoint 84, 88, 124, and 128 have 12 input buttons and 8 output buttons (figure 3-1). The CrossPoint 168 and 1616 have 16 input buttons and 16 output buttons (figure 3-2).

1			9
					INPUTS
											CONTROL					I/O
						INPUTS
1	2	3	4	5	6	7	8	9	10	11	12
												CONTROL					I/O
1	2	3	4	5	6	7	8				ENTER	PRESET	VIEW	ESC		RGBHV	AUDIO
				OUTPUTS
		OUTPUTS											CROSSPOINT MATRIX SERIES SWITCHER
2						9					3	4	5	6		7	8
Figure 3-1 — Front panel, CrossPoint 128 HVA
1		9
				INPUTS
													CONTROL				I/O
																	RGBHV
				OUTPUTS
2								9					3	4	5	6	7	8
Figure 3-2 — Front Panel, CrossPoint 1616 HVA

Definitions

The following terms apply to Extron Matrix Switchers, and are used throughout this manual:

Tie — An input-to-output connection.

Set of ties — An input tied to two or more outputs. (An output can never be tied to more than one input.)

Configuration — May consist of one tie or one or more sets of ties.

3-2 CrossPoint Matrix Switchers • Operation

Image 22

Contents CrossPoint Matrix Switchers CrossPoint 84, 88, 124, 128, 168, and 1616 HV and HVASicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start CrossPoint Matrix Switchers QS-1Quick Start CrossPoint Matrix Switchers, cont’d Table of Contents Table of Contents, cont’d One CrossPoint Matrix Switchers Introduction About the CrossPoint Series Matrix SwitchersIntroductiontroduction, cont’d Features Extron CrossPoint 128 HVAIntroduction, cont’d VCRCrossPoint Matrix Switchers Introduction Introduction, cont’d Two Power connection Installationstallation, cont’dRack Mounting the Switcher CrossPoint Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyRS-232/422 connection Installation, cont’dAdditional rear panel views Rear panel view, CrossPoint 84HV 11 Rear panel view, CrossPoint 124HVA 14 Rear panel view, CrossPoint 168HVA Installation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsCrossPoint Matrix Switchers Operation DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsControls Operation, cont’dFront panel I/O label windows Creating a configuration PowerFront Panel Operations Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step D Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets Example 6 Save a presetExample 7 Recall a preset Viewing and adjusting the audio level HVA models onlyExample 8 View and adjust an audio level = blinking value 1dB = on value 2dB = flash once 16 +8dB displayed, CrossPoint 168 System reset to factory defaults TroubleshootingFront panel security lockout executive mode Rear Panel ControlsGeneral checks Plasma display S-video problemWorksheets Worksheet example 1 Entering system equipment20 Worksheet example 2 Status meeting configuration Worksheet example 2 Drawing tiesWorksheet example 3 Test configuration System testOperation, cont’d Matrix Switchers Configuration Worksheet Input sources Output destinationsOperation, cont’d Four CrossPoint Matrix Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableCommand Ascii Command Response Additional description Command/Response TableProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Resets Five Using the software Overview Matrix Switcher+ Control ProgramInstalling the software CrossPoint Matrix Switchers Matrix SoftwareExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusUsing the software Using emulation modeUsing the help system Button-Label GeneratorExtron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Matrix Switchers SpecificationsAudio input audio models only Audio audio models onlyAudio output audio models only Specifications, cont’d Part NumbersCables Extron Part BNC-5 Mini HR Cable AppendixBB ReferenceInformation,co t’d Hardware UpgradesOpening the switcher Opening the CrossPoint 84, 88, 124,CrossPoint Matrix Switchers Reference Information Opening the CrossPoint 168Reference Information, cont’d Closing the switcherSwapping the serial ports Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Replacing the AC fuse CrossPoint 84, 88, 124, and 128 onlyFigure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA