Extron electronic 84, 88, 124, 128, 168, 1616 HV, 1616HVA, CrossPoint 88, CrossPoint 168 Cables

Page 59

Cables

When using signals with a scanning frequency of 15-125 kHz and running distances of 100 feet or more, use high resolution BNC cables to achieve maximum performance.

Bulk cable

	Extron Part	Part #
	RG6 super high resolution cable
	Bulk RG6-1, 500’	22-098-02
	Bulk RG6-1, 1000’	22-098-03
	Bulk RG6-4, 500’	22-099-02
	Bulk RG6-5, 500’	22-100-02
	RG6 male crimp connectors, qty. 50	100-075-51

	BNC-4 Mini HR Cable
	Bulk BNC 4-500’ HR	22-032-02
	Bulk BNC 4-1000’ HR	22-032-03

	BNC-5 Mini HR Cable
	Bulk BNC 5-500’ HR	22-020-02
	Bulk BNC 5-1000’ HR	22-020-03

	Plenum BNC-5 Mini HR Cable
	Bulk BNC 5-500’ HRP	22-103-02
	Bulk BNC 5-1000’ HRP	22-103-03
Assorted connectors
	BNC connectors
	BNC Mini HR crimp connectors, qty. 50	100-074-51
	RG6 male crimp connectors, qty. 50	100-075-51
	BNC bulkhead connectors, qty. 50
	(for custom wall plates)	100-076-51

Pre-cut cables

BNC-4 Mini HR cable is used for RGBS cable runs, and BNC-5 Mini HR cable is used for RGBHV cable runs. Either type can also be used for composite video, S-video, or RGsB. All Extron BNC cables have male connectors on both ends. A plenum version of the BNC-5 Mini HR cable is also available.

BNC-4 Mini HR Cable

BNC-4-25’ MHR (25 feet/7.5 meters)	26-210-04
BNC-4-50’ MHR (50 feet/15.0 meters)	26-210-05
BNC-4-75’ MHR (75 feet/23.0 meters)	26-210-06
BNC-4-100’ MHR (100 feet/30.0 meters)	26-210-07
BNC-4-150’ MHR (150 feet/45.0 meters)	26-210-08
BNC-4-200’ MHR (200 feet/60.0 meters)	26-210-09
BNC-4-250’ MHR (250 feet/75.0 meters)	26-210-54
BNC-4-300’ MHR (300 feet/90.0 meters)	26-210-53

CrossPoint Matrix Switchers • Specifications

A-5

Image 59

Contents CrossPoint 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschQS-1 Quick Start CrossPoint Matrix SwitchersQuick Start CrossPoint Matrix Switchers, cont’d Table of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the CrossPoint Series Matrix SwitchersCrossPoint Matrix Switchers Introduction Extron CrossPoint 128 HVA FeaturesVCR Introduction, cont’dCrossPoint Matrix Switchers Introduction Introduction, cont’d Two CrossPoint Matrix Switchers Installation Installationstallation, cont’dRack Mounting the Switcher Power connectionAudio input and output connections HVA models only Video input and output connectionsAdditional rear panel views Installation, cont’dRS-232/422 connection Rear panel view, CrossPoint 84HV 11 Rear panel view, CrossPoint 124HVA 14 Rear panel view, CrossPoint 168HVA Installation, cont’d Three Definitions Front Panel Controls and IndicatorsCrossPoint Matrix Switchers Operation Operationeration, cont’dControl buttons and LEDs Input buttons, output buttons, and LEDsFront panel I/O label windows Operation, cont’dControls Front Panel Operations PowerCreating a configuration Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio tiesExample 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tieExample 3, step D Removing an audio tie Viewing a configurationRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Example 6 Save a preset Using presetsExample 8 View and adjust an audio level Viewing and adjusting the audio level HVA models onlyExample 7 Recall a preset = blinking value 1dB = on value 2dB = flash once 16 +8dB displayed, CrossPoint 168 Rear Panel Controls TroubleshootingFront panel security lockout executive mode System reset to factory defaultsWorksheet example 1 Entering system equipment Plasma display S-video problemWorksheets General checksWorksheet example 2 Drawing ties 20 Worksheet example 2 Status meeting configurationSystem test Worksheet example 3 Test configurationOperation, cont’d Input sources Output destinations Matrix Switchers Configuration WorksheetOperation, cont’d Four Programmer’ser’sGuide,Guidecont’d Host-to-Switcher InstructionsSwitcher-Initiated Messages CrossPoint Matrix Switchers Programmer’s GuideUsing the Command/Response Table Switcher Error ResponsesProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Resets Five CrossPoint Matrix Switchers Matrix Software Matrix Switcher+ Control ProgramInstalling the software Using the software OverviewWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dButton-Label Generator Using emulation modeUsing the help system Using the softwareExtron’s Button-Label Generator window AAppendix a CrossPoint Matrix Switchers Specifications Specificationsecifications, cont’dAudio output audio models only Audio audio models onlyAudio input audio models only Part Numbers Specifications, cont’dCables Extron Part BNC-5 Mini HR Cable AppendixBB Opening the CrossPoint 84, 88, 124, Hardware UpgradesOpening the switcher ReferenceInformation,co t’dOpening the CrossPoint 168 CrossPoint Matrix Switchers Reference InformationSwapping the serial ports Closing the switcherReference Information, cont’d Figure B-4 Key and pin 1 mark Installing a firmware updateReplacing the AC fuse CrossPoint 84, 88, 124, and 128 only Button LabelsFigure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA