Extron electronic CrossPoint 84, CrossPoint 88 manual Using presets, Example 6 Save a preset

Page 32

Operation, cont’d

Press

					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12

F

VIEW

CONTROL

I/O

1

2

3

4

5

6

7

8

ENTER PRESET VIEW ESC

RGBHV AUDIO

OUTPUTS

Hold B Hold B

3 4

Hold Hold

3 4

3 4

D

D

E

E

F

LED key: = off,

= on, B = blinking,

Figure 3-12 — Example 5, step D: Muting and unmuting outputs

Using presets

The current configuration (configuration 0) can be saved as a preset in any one of 12 preset memory addresses (CrossPoint 84, 88, 124, and 128) or 16 preset memory addresses (CrossPoint 168 and 1616). Each CrossPoint switcher has as many presets as input buttons.

1. Only the audio and video ties are stored and recalled; audio gain settings are not saved, and do not change when a preset is recalled.

2.Presets cannot be viewed from the front panel unless recalled as the current configuration. Presets can be viewed using Extron’s Windows- based control program, see chapter 5, Matrix Software, for more details.

3.The current configuration and all presets are stored in non-volatile memory. When power is removed and restored, the current configuration is still active and all presets are retained.

4.When a preset is recalled, it replaces the current configuration, which is lost unless it is also stored as a preset. The recalled preset overwrites all of the current configuration ties in favor of the preset configuration ties.

Example 6: Save a preset

See figure 3-13 and the following steps for an example of saving the current configuration as a preset.

1
F				LED key:			= off,			= on,	B = blinking,
Press							F = flash once
		C					F = flash once
		C
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12
1	2	3	4	5	6	7	8
			OUTPUTS

C

Hold B	F Press
B	A
PRESET	ESC
CONTROL	I/O
ENTER PRESET VIEW	ESC RGBHV AUDIO

Figure 3-13 — Example 6: Saving the current configuration as preset 1

3-12 CrossPoint Matrix Switchers • Operation

Image 32

Contents CrossPoint Matrix Switchers CrossPoint 84, 88, 124, 128, 168, and 1616 HV and HVASafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start CrossPoint Matrix Switchers QS-1Quick Start CrossPoint Matrix Switchers, cont’d Table of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the CrossPoint Series Matrix SwitchersCrossPoint Matrix Switchers Introduction Features Extron CrossPoint 128 HVAIntroduction, cont’d VCRCrossPoint Matrix Switchers Introduction Introduction, cont’d Two Installationstallation, cont’d Rack Mounting the SwitcherPower connection CrossPoint Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyAdditional rear panel views Installation, cont’dRS-232/422 connection Rear panel view, CrossPoint 84HV 11 Rear panel view, CrossPoint 124HVA 14 Rear panel view, CrossPoint 168HVA Installation, cont’d Three Front Panel Controls and Indicators CrossPoint Matrix Switchers OperationOperationeration, cont’d DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsFront panel I/O label windows Operation, cont’dControls Front Panel Operations PowerCreating a configuration Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step D Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets Example 6 Save a presetExample 8 View and adjust an audio level Viewing and adjusting the audio level HVA models onlyExample 7 Recall a preset = blinking value 1dB = on value 2dB = flash once 16 +8dB displayed, CrossPoint 168 Troubleshooting Front panel security lockout executive modeSystem reset to factory defaults Rear Panel ControlsPlasma display S-video problem WorksheetsGeneral checks Worksheet example 1 Entering system equipment20 Worksheet example 2 Status meeting configuration Worksheet example 2 Drawing tiesWorksheet example 3 Test configuration System testOperation, cont’d Matrix Switchers Configuration Worksheet Input sources Output destinationsOperation, cont’d Four Host-to-Switcher Instructions Switcher-Initiated MessagesCrossPoint Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Resets Five Matrix Switcher+ Control Program Installing the softwareUsing the software Overview CrossPoint Matrix Switchers Matrix SoftwareExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusUsing emulation mode Using the help systemUsing the software Button-Label GeneratorExtron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Matrix Switchers SpecificationsAudio output audio models only Audio audio models onlyAudio input audio models only Specifications, cont’d Part NumbersCables Extron Part BNC-5 Mini HR Cable AppendixBB Hardware Upgrades Opening the switcherReferenceInformation,co t’d Opening the CrossPoint 84, 88, 124,CrossPoint Matrix Switchers Reference Information Opening the CrossPoint 168Swapping the serial ports Closing the switcherReference Information, cont’d Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Replacing the AC fuse CrossPoint 84, 88, 124, and 128 onlyFigure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA