Extron electronic CrossPoint 88 manual Operation, cont’d, Controls, Front panel I/O label windows

Page 24

Operation, cont’d

As a secondary function on HVA models, the Esc button increments the audio level of the selected input. In audio adjust mode, the Esc LED indicates a positive (+) gain value. A more detailed explanation of audio level adjustment is included in Viewing and adjusting the audio level (HVA models only) on page 3-13.

I/O controls

When creating or viewing a configuration, you must specify whether the configuration applies to video, audio, or both. This is done with the RGBHV (7) and Audio (8) buttons.

Although present, the Audio button has no function on HV models.

7RGBHV button and LED — The RGBHV button selects and deselects video for a configuration being created or viewed. The RGBHV LED lights to indicate that video is available for configuration or viewing.

8Audio button and LED — The Audio button selects and deselects audio for a configuration that is being created or viewed. The Audio LED lights to indicate that the audio configuration follows the video configuration. The Audio LED blinks to indicate that the audio configuration is broken away from the video configuration.

As a secondary function, the Audio button selects the audio level display/ adjust mode. Press and hold the Audio button until the Audio LED begins to blink. If the RGBHV LED was lit, it turns off. Select an input. The current audio level setting for the selected input is displayed in the output LEDs. The audio level for the selected input can be incremented and decremented by pressing the View (5) and Esc (6) buttons. A more detailed explanation of audio level adjustment is included in Viewing and adjusting the audio level (HVA models only) on page 3-13.

Front panel I/O label windows

9Input and output label windows — These translucent panels can be removed and replaced to insert labels behind the panels. To remove a panel, insert the Phillips-head end of an Extron tweeker or small Phillips-head screwdriver into the hole in one end of the panel, and gently slide the tab on the edge of the panel out of the recess in the switcher housing.

Input and output labels can be created easily with Extron’s button label generator software, which ships with every Extron Matrix Switcher, or with any Brother P-Touch labeler. Each input and output can be labeled with names, alphanumeric characters, or even color bitmaps for easy and intuitive input and output selection (figure 3-3). See chapter 5, Matrix Software, for details on using the label software.

Rack DVD (DVS 100)

INPUTS

1

2

3

4

5

6

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 3-3 — Sample label

3-4 CrossPoint Matrix Switchers • Operation

Page 23 Page 25
Image 24
Page 23 Page 25
Contents CrossPoint Matrix Switchers CrossPoint 84, 88, 124, 128, 168, and 1616 HV and HVASafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start CrossPoint Matrix Switchers QS-1Quick Start CrossPoint Matrix Switchers, cont’d Table of Contents Table of Contents, cont’d One About the CrossPoint Series Matrix Switchers CrossPoint Matrix Switchers IntroductionIntroductiontroduction, cont’d Features Extron CrossPoint 128 HVAIntroduction, cont’d VCRCrossPoint Matrix Switchers Introduction Introduction, cont’d Two Installationstallation, cont’d Rack Mounting the SwitcherPower connection CrossPoint Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyInstallation, cont’d RS-232/422 connectionAdditional rear panel views Rear panel view, CrossPoint 84HV 11 Rear panel view, CrossPoint 124HVA 14 Rear panel view, CrossPoint 168HVA Installation, cont’d Three Front Panel Controls and Indicators CrossPoint Matrix Switchers OperationOperationeration, cont’d DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsOperation, cont’d ControlsFront panel I/O label windows Power Creating a configurationFront Panel Operations Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step D Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets Example 6 Save a presetViewing and adjusting the audio level HVA models only Example 7 Recall a presetExample 8 View and adjust an audio level = blinking value 1dB = on value 2dB = flash once 16 +8dB displayed, CrossPoint 168 Troubleshooting Front panel security lockout executive modeSystem reset to factory defaults Rear Panel ControlsPlasma display S-video problem WorksheetsGeneral checks Worksheet example 1 Entering system equipment20 Worksheet example 2 Status meeting configuration Worksheet example 2 Drawing tiesWorksheet example 3 Test configuration System testOperation, cont’d Matrix Switchers Configuration Worksheet Input sources Output destinationsOperation, cont’d Four Host-to-Switcher Instructions Switcher-Initiated MessagesCrossPoint Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableCommand/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Resets Five Matrix Switcher+ Control Program Installing the softwareUsing the software Overview CrossPoint Matrix Switchers Matrix SoftwareExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusUsing emulation mode Using the help systemUsing the software Button-Label GeneratorExtron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Matrix Switchers SpecificationsAudio audio models only Audio input audio models onlyAudio output audio models only Specifications, cont’d Part NumbersCables Extron Part BNC-5 Mini HR Cable AppendixBB Hardware Upgrades Opening the switcherReferenceInformation,co t’d Opening the CrossPoint 84, 88, 124,CrossPoint Matrix Switchers Reference Information Opening the CrossPoint 168Closing the switcher Reference Information, cont’dSwapping the serial ports Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Replacing the AC fuse CrossPoint 84, 88, 124, and 128 onlyFigure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA
Top Page Image Contents