Extron electronic CrossPoint 124, CrossPoint 88 = blinking value 1dB = on value 2dB = flash once

Page 34

Operation, cont’d

the CrossPoint 168 and 1616, but the steps for displaying the value are the same. For this reason, figure 3-16 and figure 3-18 show the indications displayed on the CrossPoint 168 and 1616 without duplicating all of the actions shown in figure 3-15 and figure 3-17.

LED key:

= off (value 0 dB),

B = blinking (value 1dB),

5

= on (value 2dB),

F = flash once

Press

B

C

C

B

Press

B

INPUTS

1

2

3

4

5

6

7

8

9

10

11

12

AUDIO

CONTROL

I/O

1

2

3

4

5

6

7

8

ENTER PRESET VIEW

ESC

RGBHV AUDIO

OUTPUTS

C

Press

F

+8dB

A

ESC

Figure 3-15 — Example 8: Viewing the audio level, CrossPoint 84, 88, 124, and 128

APress and release the Esc button. The Esc LED flashes once.

BPress and hold the Audio button for approximately 2 seconds until the Audio LED begins to blink, then release the Audio button.

CPress and release the input 5 button. The input 5 LED lights. The audio level for the selected input is displayed in the output LEDs. The polarity is indicated by either the Esc () or View () LED blinking.

On the CrossPoint 84, 88, 124, and 128, each output LED indicates 1dB when blinking and 2dB when lit.

On the CrossPoint 168 and 1616, each output LED indicates 1dB when lit.

The blinking Esc () LED indicates a positive (gain) level. The blinking View () LED indicates a negative (attenuation) level.

Figure 3-15 and figure 3-16 show an audio level of +8dB displayed in the output LEDs on the two different CrossPoint front panels.

		CrossPoint 84, 88, 124, 128
				Output LED					View Esc
dB	1	2	3	4	5	6	7	8
+9					B				B
+8									B
+7				B					B
+6									B
+5			B						B
+4									B
+3		B							B
+2									B
+1	B								B
0									B
-1	B								B
-2									B
-3		B							B
-4									B
-5			B						B
-6									B
-7				B					B
-8									B
-9					B				B
-10									B
-11						B			B
-12									B
-13							B		B
-14									B
-15								B	B

3-14 CrossPoint Matrix Switchers • Operation

Image 34

Contents CrossPoint Matrix Switchers CrossPoint 84, 88, 124, 128, 168, and 1616 HV and HVASicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start CrossPoint Matrix Switchers QS-1Quick Start CrossPoint Matrix Switchers, cont’d Table of Contents Table of Contents, cont’d One CrossPoint Matrix Switchers Introduction About the CrossPoint Series Matrix SwitchersIntroductiontroduction, cont’d Features Extron CrossPoint 128 HVAIntroduction, cont’d VCRCrossPoint Matrix Switchers Introduction Introduction, cont’d Two Power connection Installationstallation, cont’dRack Mounting the Switcher CrossPoint Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyRS-232/422 connection Installation, cont’dAdditional rear panel views Rear panel view, CrossPoint 84HV 11 Rear panel view, CrossPoint 124HVA 14 Rear panel view, CrossPoint 168HVA Installation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsCrossPoint Matrix Switchers Operation DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsControls Operation, cont’dFront panel I/O label windows Creating a configuration PowerFront Panel Operations Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step D Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets Example 6 Save a presetExample 7 Recall a preset Viewing and adjusting the audio level HVA models onlyExample 8 View and adjust an audio level = blinking value 1dB = on value 2dB = flash once 16 +8dB displayed, CrossPoint 168 System reset to factory defaults TroubleshootingFront panel security lockout executive mode Rear Panel ControlsGeneral checks Plasma display S-video problemWorksheets Worksheet example 1 Entering system equipment20 Worksheet example 2 Status meeting configuration Worksheet example 2 Drawing tiesWorksheet example 3 Test configuration System testOperation, cont’d Matrix Switchers Configuration Worksheet Input sources Output destinationsOperation, cont’d Four CrossPoint Matrix Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableCommand Ascii Command Response Additional description Command/Response TableProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Resets Five Using the software Overview Matrix Switcher+ Control ProgramInstalling the software CrossPoint Matrix Switchers Matrix SoftwareExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusUsing the software Using emulation modeUsing the help system Button-Label GeneratorExtron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Matrix Switchers SpecificationsAudio input audio models only Audio audio models onlyAudio output audio models only Specifications, cont’d Part NumbersCables Extron Part BNC-5 Mini HR Cable AppendixBB ReferenceInformation,co t’d Hardware UpgradesOpening the switcher Opening the CrossPoint 84, 88, 124,CrossPoint Matrix Switchers Reference Information Opening the CrossPoint 168Reference Information, cont’d Closing the switcherSwapping the serial ports Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Replacing the AC fuse CrossPoint 84, 88, 124, and 128 onlyFigure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA