Extron electronic 84, 88, 124, 128, 168, 1616 HV, 1616HVA, CrossPoint 88 manual Rgbhv Audio View

Page 29

		LED key:			= off,			= on,				Press	Press
					F = flashes once						Press		C
											Press		C
					INPUTS						B	RGBHV	AUDIO
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12	VIEW
												VIEW

CONTROL

I/O

1 2

3

4

5

6

7

8

ENTER PRESET VIEW ESC

RGBHV AUDIO

OUTPUTS

C	Press	F
	Press

2

5

6

7

A

ESC

Figure 3-8 — Example 4: Viewing the current configuration, no input selected

Example 4 shows the process of viewing the current configuration after the steps in Examples 1, 2, and 3 have been performed.

APress and release the Esc button. The Esc LED flashes once.

BPress and release the View button to enter view-only mode. The View LED lights.

CIf necessary to select both video and audio for viewing, press and release the RGBHV and Audio buttons until the RGBHV LED and Audio LED light. With no input LED selected, all output LEDs that have no established ties light.

DPress and release the input 5 button (figure 3-9). The input 5 LED lights.

If ties are established for input 5, all output LEDs toggle; outputs with no ties turn off and the LEDs associated with all outputs tied to input 5 (audio, video, or audio and video ties) light. If no ties are established for input 5, all output LEDs turn off.

If audio is broken away, the Audio LED blinks.

				5
			Press					LED key:			= off,	= on, B = blinking
			D
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12

B D

RGBHV AUDIO

CONTROL

I/O

1

2

3

4

5

6

7

8

OUTPUTS

ENTER PRESET VIEW ESC

RGBHV AUDIO

D

1

3

4

8

Figure 3-9 — Example 4, step D: Viewing the current configuration, video and audio

A set of ties can also be viewed by selecting a tied output. To demonstrate this, note the number of a lit output LED and press and release the output button for an unlit (untied) output LED. Observe that all of the untied outputs light. Then press the output button for the output LED noted previously and observe

CrossPoint Matrix Switchers • Operation

3-9

Image 29

Contents CrossPoint 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Matrix SwitchersConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQS-1 Quick Start CrossPoint Matrix SwitchersQuick Start CrossPoint Matrix Switchers, cont’d Table of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the CrossPoint Series Matrix SwitchersCrossPoint Matrix Switchers Introduction Extron CrossPoint 128 HVA FeaturesVCR Introduction, cont’dCrossPoint Matrix Switchers Introduction Introduction, cont’d Two Rack Mounting the Switcher Installationstallation, cont’dPower connection CrossPoint Matrix Switchers InstallationAudio input and output connections HVA models only Video input and output connectionsAdditional rear panel views Installation, cont’dRS-232/422 connection Rear panel view, CrossPoint 84HV 11 Rear panel view, CrossPoint 124HVA 14 Rear panel view, CrossPoint 168HVA Installation, cont’d Three CrossPoint Matrix Switchers Operation Front Panel Controls and IndicatorsOperationeration, cont’d DefinitionsControl buttons and LEDs Input buttons, output buttons, and LEDsFront panel I/O label windows Operation, cont’dControls Front Panel Operations PowerCreating a configuration Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio tiesExample 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tieExample 3, step D Removing an audio tie Viewing a configurationRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Example 6 Save a preset Using presetsExample 8 View and adjust an audio level Viewing and adjusting the audio level HVA models onlyExample 7 Recall a preset = blinking value 1dB = on value 2dB = flash once 16 +8dB displayed, CrossPoint 168 Front panel security lockout executive mode TroubleshootingSystem reset to factory defaults Rear Panel ControlsWorksheets Plasma display S-video problemGeneral checks Worksheet example 1 Entering system equipmentWorksheet example 2 Drawing ties 20 Worksheet example 2 Status meeting configurationSystem test Worksheet example 3 Test configurationOperation, cont’d Input sources Output destinations Matrix Switchers Configuration WorksheetOperation, cont’d Four Switcher-Initiated Messages Host-to-Switcher InstructionsCrossPoint Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dUsing the Command/Response Table Switcher Error ResponsesProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Resets Five Installing the software Matrix Switcher+ Control ProgramUsing the software Overview CrossPoint Matrix Switchers Matrix SoftwareWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dUsing the help system Using emulation modeUsing the software Button-Label GeneratorExtron’s Button-Label Generator window AAppendix a CrossPoint Matrix Switchers Specifications Specificationsecifications, cont’dAudio output audio models only Audio audio models onlyAudio input audio models only Part Numbers Specifications, cont’dCables Extron Part BNC-5 Mini HR Cable AppendixBB Opening the switcher Hardware UpgradesReferenceInformation,co t’d Opening the CrossPoint 84, 88, 124,Opening the CrossPoint 168 CrossPoint Matrix Switchers Reference InformationSwapping the serial ports Closing the switcherReference Information, cont’d Figure B-4 Key and pin 1 mark Installing a firmware updateReplacing the AC fuse CrossPoint 84, 88, 124, and 128 only Button LabelsFigure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA