Extron electronic CrossPoint 84, CrossPoint 88, CrossPoint 168 Specificationsecifications, cont’d

Page 56

Specificationsecifications, cont’d

Video

Routing	84 Series	8 x 4 matrix
	88 Series	8 x 8 matrix
	124 Series	12 x 4 matrix
	128 Series	12 x 8 matrix
	168 Series	16 x 8 matrix
	1616 Series	16 x 16 matrix
Gain	Unity
Bandwidth	200 MHz (-3dB), fully loaded
	0 - 10 MHz	no more than +0.1dB to -0.1dB
	0 - 130 MHz	no more than +6dB to -0.8dB
Crosstalk	-50dB @ 5 MHz, -45dB @ 10 MHz
Switching speed	200 nS (max.)

Video input

Number/signal type	8, 12, or 16 RGBHV, RGBS, RGsB, RsGsBs, HDTV, component video,
	S-video, composite video
Connectors	84/88 Series	..............	8 x 5 BNC female
	124/128 Series		12 x 5 BNC female
	168/1616 Series		16 x 5 BNC female
Nominal level	1V p-p for Y of component video and S-video, and for composite video
	0.7V p-p for RGB
	0.3V p-p for R-Y and B-Y of component video, and for C of S-video
Minimum/maximum levels	Analog	0.5V to 2.0V p-p
Impedance	75 ohms
Return loss	-30dB @ 5 MHz
Maximum DC offset	1.5V

Video output

Number/signal type	4, 8, or 16 RGBHV, RGBS, RGsB, RsGsBs, HDTV, component video, S-video,
	composite video
Connectors	84/124 Series	4 x 5 BNC female
	88/128 Series	8 x 5 BNC female
	168 Series	8 x 5 BNC female
	1616 Series	16 x 5 BNC female
Nominal level	1V p-p for Y of component video and S-video, and for composite video
	0.7V p-p for RGB
	0.3V p-p for R-Y and B-Y of component video, and for C of S-video
Minimum/maximum level	2V p-p
Impedance	75 ohms
Return loss	-30dB @ 5 MHz
DC offset	±5mV maximum with input at 0 offset

Sync

Input/output type	RGBHV, RGBS, RGsB, RsGsBs
Input level	0.5V to 5.0V p-p, 4.0V p-p normal
Output level	AGC to TTL: 4V to 5V p-p, unterminated
Input impedance
84/88/124/128 Series	All inputs	510 ohms
168/1616 Series	Inputs 1, 3, 5, 7	75 or 510 ohms, switchable
	Inputs 2, 4, 6, 8, and 9 through 16	510 ohms
Output impedance	75 ohms
Polarity	Positive or negative (follows input)

A-2 CrossPoint Matrix Switchers • Specifications

Image 56

Contents CrossPoint Matrix Switchers CrossPoint 84, 88, 124, 128, 168, and 1616 HV and HVASafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start CrossPoint Matrix Switchers QS-1Quick Start CrossPoint Matrix Switchers, cont’d Table of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the CrossPoint Series Matrix SwitchersCrossPoint Matrix Switchers Introduction Features Extron CrossPoint 128 HVAIntroduction, cont’d VCRCrossPoint Matrix Switchers Introduction Introduction, cont’d Two Installationstallation, cont’d Rack Mounting the SwitcherPower connection CrossPoint Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyAdditional rear panel views Installation, cont’dRS-232/422 connection Rear panel view, CrossPoint 84HV 11 Rear panel view, CrossPoint 124HVA 14 Rear panel view, CrossPoint 168HVA Installation, cont’d Three Front Panel Controls and Indicators CrossPoint Matrix Switchers OperationOperationeration, cont’d DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsFront panel I/O label windows Operation, cont’dControls Front Panel Operations PowerCreating a configuration Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step D Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets Example 6 Save a presetExample 8 View and adjust an audio level Viewing and adjusting the audio level HVA models onlyExample 7 Recall a preset = blinking value 1dB = on value 2dB = flash once 16 +8dB displayed, CrossPoint 168 Troubleshooting Front panel security lockout executive modeSystem reset to factory defaults Rear Panel ControlsPlasma display S-video problem WorksheetsGeneral checks Worksheet example 1 Entering system equipment20 Worksheet example 2 Status meeting configuration Worksheet example 2 Drawing tiesWorksheet example 3 Test configuration System testOperation, cont’d Matrix Switchers Configuration Worksheet Input sources Output destinationsOperation, cont’d Four Host-to-Switcher Instructions Switcher-Initiated MessagesCrossPoint Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Resets Five Matrix Switcher+ Control Program Installing the softwareUsing the software Overview CrossPoint Matrix Switchers Matrix SoftwareExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusUsing emulation mode Using the help systemUsing the software Button-Label GeneratorExtron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Matrix Switchers SpecificationsAudio output audio models only Audio audio models onlyAudio input audio models only Specifications, cont’d Part NumbersCables Extron Part BNC-5 Mini HR Cable AppendixBB Hardware Upgrades Opening the switcherReferenceInformation,co t’d Opening the CrossPoint 84, 88, 124,CrossPoint Matrix Switchers Reference Information Opening the CrossPoint 168Swapping the serial ports Closing the switcherReference Information, cont’d Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Replacing the AC fuse CrossPoint 84, 88, 124, and 128 onlyFigure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA