Extron electronic CrossPoint 88, CrossPoint 168, CrossPoint 84, CrossPoint 128 manual Button Labels

Page 66

Reference Information, cont’d

If you choose to check for proper operation before putting the cover back on, ensure that tools and hands are outside the switcher and then perform step 11. After recognizing the new IC, the switcher should power up normally. Unplug the AC power cord, and reinstall the switcher.

11.Reinitialize the switcher to recognize the new IC as follows: a. Connect the power cord to the AC power source.

b. Press and hold the Enter button while you connect the power cord to the switcher.

c. Observe that the Input, Output, Preset, View, and Esc LEDs all flash.

d. Release the Enter button.

12. Ensure that the switcher is working properly.

13.If the switcher was removed from a rack, remove its power cord, reattach the switcher to the rack, and reconnect the power cord.

14. Reconnect the input and output cables.

Replacing the AC fuse (CrossPoint 84, 88, 124, and 128 only)

The AC fuse on the power supply board is a user-replaceable component of the CrossPoint 84, 88, 124, and 128. To replace the AC fuse, do the following:

1.Follow the instructions in Opening the CrossPoint 84, 88, 124, and 128 on page B-2 to remove the top cover.

2.Locate the fuse on the power supply board (see figure B-1), and remove it from its retaining clips.

3.If test equipment is available, you can check the fuse.

4.Place a new 2A/250V fast-blow fuse in the retaining clips.

5.Reinstall the switcher’s cover. See Closing the switcher on page B-4.

If you choose to check the switcher for proper operation before putting the cover back on, ensure that tools and hands are outside the switcher, and then connect the power cord to the unit and to an AC source. The switcher should power up normally. Unplug the AC power cord, and reinstall the switcher.

6.Attach the power cord to the switcher and to the AC power source. Make sure the switcher is working properly.

7.If the switcher was removed from a rack, remove its power cord, reattach the switcher to the rack, and reconnect the power cord.

8.

Reconnect the input and output cables.

Button Labels

Figure B-5 provides blanks of a 16-button strip of button labels. Feel free to photocopy them or cut them out of the manual, write button information in each button area as desired, and put them in the switcher’s label window. For 8-button strips and 12-button strips, use scissors to trim the blank to the appropriate length.

B-6 CrossPoint Matrix Switchers • Reference Information

Image 66
Contents CrossPoint Matrix Switchers CrossPoint 84, 88, 124, 128, 168, and 1616 HV and HVASicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start CrossPoint Matrix Switchers QS-1Quick Start CrossPoint Matrix Switchers, cont’d Table of Contents Table of Contents, cont’d One About the CrossPoint Series Matrix Switchers CrossPoint Matrix Switchers IntroductionIntroductiontroduction, cont’d Features Extron CrossPoint 128 HVAIntroduction, cont’d VCRCrossPoint Matrix Switchers Introduction Introduction, cont’d Two Power connection Installationstallation, cont’dRack Mounting the Switcher CrossPoint Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyInstallation, cont’d RS-232/422 connectionAdditional rear panel views Rear panel view, CrossPoint 84HV 11 Rear panel view, CrossPoint 124HVA 14 Rear panel view, CrossPoint 168HVA Installation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsCrossPoint Matrix Switchers Operation DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsOperation, cont’d ControlsFront panel I/O label windows Power Creating a configurationFront Panel Operations Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step D Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets Example 6 Save a presetViewing and adjusting the audio level HVA models only Example 7 Recall a presetExample 8 View and adjust an audio level = blinking value 1dB = on value 2dB = flash once 16 +8dB displayed, CrossPoint 168 System reset to factory defaults TroubleshootingFront panel security lockout executive mode Rear Panel ControlsGeneral checks Plasma display S-video problemWorksheets Worksheet example 1 Entering system equipment20 Worksheet example 2 Status meeting configuration Worksheet example 2 Drawing tiesWorksheet example 3 Test configuration System testOperation, cont’d Matrix Switchers Configuration Worksheet Input sources Output destinationsOperation, cont’d Four CrossPoint Matrix Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableCommand/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Resets Five Using the software Overview Matrix Switcher+ Control ProgramInstalling the software CrossPoint Matrix Switchers Matrix SoftwareExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusUsing the software Using emulation modeUsing the help system Button-Label GeneratorExtron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Matrix Switchers SpecificationsAudio audio models only Audio input audio models onlyAudio output audio models only Specifications, cont’d Part NumbersCables Extron Part BNC-5 Mini HR Cable AppendixBB ReferenceInformation,co t’d Hardware UpgradesOpening the switcher Opening the CrossPoint 84, 88, 124,CrossPoint Matrix Switchers Reference Information Opening the CrossPoint 168Closing the switcher Reference Information, cont’dSwapping the serial ports Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Replacing the AC fuse CrossPoint 84, 88, 124, and 128 onlyFigure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA