Extron electronic CrossPoint 128, CrossPoint 88, CrossPoint 168 manual Example 2 Adding a video tie

Page 27

output 3, output 4, and output 8; and audio input 5 tied to audio output 3, output 4, and output 8.

				5			LED key:			= off,	= on, B = blinking,		Press
							LED key:			= off,	= on, B = blinking,		Press
			Press						F	= flash once			B
									F	= flash once
						C
						C							RGBHV
					INPUTS								RGBHV
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12
												CONTROL	I/O
1	2	3	4	5	6	7	8					ENTER PRESET VIEW	ESC RGBHV AUDIO
			OUTPUTS
				C				C			Press	Press	F
B		3	4				8				Press	Press	F
B		3	4				8
Press												E	A
												E	A

D

1

ENTER ESC

Figure 3-5 — Example 2: Adding a video tie

Example 3: Remove a tie from a set of video and audio ties

See figure 3-6 and the following steps for an example in which an existing audio tie is removed from the current configuration.

				5					LED key:		= off,	= on,
									LED key:		= off,	= on,
			Press								F = flash once
						C
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12

Press

B

AUDIO

CONTROL				I/O

1 2

3

4

5

6

7

8

OUTPUTS

ENTER PRESET VIEW ESC

RGBHV AUDIO

	C	C	Press	F
3	4	8

ESC

Figure 3-6 — Example 3: Selecting audio, selecting input 5

A

APress and release the Esc button. The Esc LED flashes once.

BIf necessary to select audio-only for the tie, press and release the RGBHV and Audio buttons until the RGBHV LED is off and the Audio LED lights.

CPress and release the input 5 button. The input 5 LED lights. If the steps in Example 1 have been completed, the output 3, output 4, and output 8 LEDs light to indicate ties created in Example 1.

The output 1 LED does not light even if the steps in Example 2 were completed because Example 2 added a video tie only.

DPress and release the output 4 button (figure 3-7). The output 4 LED turns off, while the output 3 and output 8 LEDs remain lit.

CrossPoint Matrix Switchers • Operation

3-7

Image 27

Contents CrossPoint 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschQS-1 Quick Start CrossPoint Matrix SwitchersQuick Start CrossPoint Matrix Switchers, cont’d Table of Contents Table of Contents, cont’d One About the CrossPoint Series Matrix Switchers CrossPoint Matrix Switchers IntroductionIntroductiontroduction, cont’d Extron CrossPoint 128 HVA FeaturesVCR Introduction, cont’dCrossPoint Matrix Switchers Introduction Introduction, cont’d Two CrossPoint Matrix Switchers Installation Installationstallation, cont’dRack Mounting the Switcher Power connectionAudio input and output connections HVA models only Video input and output connectionsInstallation, cont’d RS-232/422 connectionAdditional rear panel views Rear panel view, CrossPoint 84HV 11 Rear panel view, CrossPoint 124HVA 14 Rear panel view, CrossPoint 168HVA Installation, cont’d Three Definitions Front Panel Controls and IndicatorsCrossPoint Matrix Switchers Operation Operationeration, cont’dControl buttons and LEDs Input buttons, output buttons, and LEDsOperation, cont’d ControlsFront panel I/O label windows Power Creating a configurationFront Panel Operations Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio tiesExample 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tieExample 3, step D Removing an audio tie Viewing a configurationRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Example 6 Save a preset Using presetsViewing and adjusting the audio level HVA models only Example 7 Recall a presetExample 8 View and adjust an audio level = blinking value 1dB = on value 2dB = flash once 16 +8dB displayed, CrossPoint 168 Rear Panel Controls TroubleshootingFront panel security lockout executive mode System reset to factory defaultsWorksheet example 1 Entering system equipment Plasma display S-video problemWorksheets General checksWorksheet example 2 Drawing ties 20 Worksheet example 2 Status meeting configurationSystem test Worksheet example 3 Test configurationOperation, cont’d Input sources Output destinations Matrix Switchers Configuration WorksheetOperation, cont’d Four Programmer’ser’sGuide,Guidecont’d Host-to-Switcher InstructionsSwitcher-Initiated Messages CrossPoint Matrix Switchers Programmer’s GuideUsing the Command/Response Table Switcher Error ResponsesCommand/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Resets Five CrossPoint Matrix Switchers Matrix Software Matrix Switcher+ Control ProgramInstalling the software Using the software OverviewWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dButton-Label Generator Using emulation modeUsing the help system Using the softwareExtron’s Button-Label Generator window AAppendix a CrossPoint Matrix Switchers Specifications Specificationsecifications, cont’dAudio audio models only Audio input audio models onlyAudio output audio models only Part Numbers Specifications, cont’dCables Extron Part BNC-5 Mini HR Cable AppendixBB Opening the CrossPoint 84, 88, 124, Hardware UpgradesOpening the switcher ReferenceInformation,co t’dOpening the CrossPoint 168 CrossPoint Matrix Switchers Reference InformationClosing the switcher Reference Information, cont’dSwapping the serial ports Figure B-4 Key and pin 1 mark Installing a firmware updateReplacing the AC fuse CrossPoint 84, 88, 124, and 128 only Button LabelsFigure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA