Extron electronic 84, 88, 124, 128, 168, 1616 HV, 1616HVA manual 16 +8dB displayed, CrossPoint 168

Page 35

				5		LED key:			= off (value 0dB),				B	= blinking,
				5					= on (value 1dB)
									= on (value 1dB)
								INPUTS
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
							OUTPUTS

C

+8dB

B	C
	B
TROL	I/O
VIEW ESC	RGBHV AUDIO

Figure 3-16 — +8dB displayed, CrossPoint 168 and 1616

DPress and release the View () button once to decrease the audio level displayed in the output LEDs by 1dB. Press and release the View () button several more times to decrease the audio level displayed in the output LEDs by an additional 1dB per button push. Note the output LED, View LED, and Esc LED changes that occur each time the View () button is pressed and released. Figure 3-17 and figure 3-18 show the result of pressing the View () button a total of 9 times. Both figures show an audio level of -1dB. Note that the Esc () LED has turned off and that the View () LED is blinking to indicate a negative level.

LED key:

= off (value 0 dB), B = blinking (value 1dB),

= on (value 2dB)

					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12

Press

E

RGBHV AUDIO

D B

CONTROL

I/O

1	2	3	4	5	6	7	8
			OUTPUTS

B

-1dB

ENTER PRESET VIEW

ESC

RGBHV AUDIO

D

D

Press

9 times VIEW

Figure 3-17 — Example 8, step D: Adjusting the audio level, CrossPoint 84, 88, 124, and 128

				5		LED key:			= off (value 0dB),				B	= blinking,
				5					= on (value 1dB)
									= on (value 1dB)
								INPUTS
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
							OUTPUTS

D

-1dB

B D

	B
TROL	I/O
VIEW ESC	RGBHV AUDIO

Figure 3-18 — -1dB displayed, CrossPoint 168 and CrossPoint 1616

CrossPoint Matrix Switchers • Operation 3-15

Image 35

Contents CrossPoint 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschQS-1 Quick Start CrossPoint Matrix SwitchersQuick Start CrossPoint Matrix Switchers, cont’d Table of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the CrossPoint Series Matrix SwitchersCrossPoint Matrix Switchers Introduction Extron CrossPoint 128 HVA FeaturesVCR Introduction, cont’dCrossPoint Matrix Switchers Introduction Introduction, cont’d Two CrossPoint Matrix Switchers Installation Installationstallation, cont’dRack Mounting the Switcher Power connectionAudio input and output connections HVA models only Video input and output connectionsAdditional rear panel views Installation, cont’dRS-232/422 connection Rear panel view, CrossPoint 84HV 11 Rear panel view, CrossPoint 124HVA 14 Rear panel view, CrossPoint 168HVA Installation, cont’d Three Definitions Front Panel Controls and IndicatorsCrossPoint Matrix Switchers Operation Operationeration, cont’dControl buttons and LEDs Input buttons, output buttons, and LEDsFront panel I/O label windows Operation, cont’dControls Front Panel Operations PowerCreating a configuration Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio tiesExample 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tieExample 3, step D Removing an audio tie Viewing a configurationRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Example 6 Save a preset Using presetsExample 8 View and adjust an audio level Viewing and adjusting the audio level HVA models onlyExample 7 Recall a preset = blinking value 1dB = on value 2dB = flash once 16 +8dB displayed, CrossPoint 168 Rear Panel Controls TroubleshootingFront panel security lockout executive mode System reset to factory defaultsWorksheet example 1 Entering system equipment Plasma display S-video problemWorksheets General checksWorksheet example 2 Drawing ties 20 Worksheet example 2 Status meeting configurationSystem test Worksheet example 3 Test configurationOperation, cont’d Input sources Output destinations Matrix Switchers Configuration WorksheetOperation, cont’d Four Programmer’ser’sGuide,Guidecont’d Host-to-Switcher InstructionsSwitcher-Initiated Messages CrossPoint Matrix Switchers Programmer’s GuideUsing the Command/Response Table Switcher Error ResponsesProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Resets Five CrossPoint Matrix Switchers Matrix Software Matrix Switcher+ Control ProgramInstalling the software Using the software OverviewWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dButton-Label Generator Using emulation modeUsing the help system Using the softwareExtron’s Button-Label Generator window AAppendix a CrossPoint Matrix Switchers Specifications Specificationsecifications, cont’dAudio output audio models only Audio audio models onlyAudio input audio models only Part Numbers Specifications, cont’dCables Extron Part BNC-5 Mini HR Cable AppendixBB Opening the CrossPoint 84, 88, 124, Hardware UpgradesOpening the switcher ReferenceInformation,co t’dOpening the CrossPoint 168 CrossPoint Matrix Switchers Reference InformationSwapping the serial ports Closing the switcherReference Information, cont’d Figure B-4 Key and pin 1 mark Installing a firmware updateReplacing the AC fuse CrossPoint 84, 88, 124, and 128 only Button LabelsFigure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA