Extron electronic CrossPoint 88, CrossPoint 168 manual Muting and unmuting video and/or audio

Page 30

Operation, cont’d

that the selected output LED, the tied input LED (input 5), and the output LEDs light for all of the outputs that are tied to the input.

EPress and release the RGBHV button to toggle the Video LED off (figure 3-10). If audio is broken away, the Audio LED stops blinking and lights.

If audio ties are established for input 5, the output LEDs for all audio outputs tied to input 5 light. If no ties are established for input 5, all output LEDs turn off.

								LED key:			= off,	= on
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12
1	2	3	4	5	6	7	8
			OUTPUTS

E

38

	Press
	E
	RGBHV AUDIO
CONTROL	I/O
ENTER PRESET VIEW	ESC RGBHV AUDIO

Figure 3-10 — Example 4, step E: Viewing the current configuration, audio-only

FPress and release the RGBHV and Audio buttons to toggle the Video LED on and the Audio LED off (figure 3-11).

If video ties are established for input 5, the output LEDs for all video outputs tied to input 5 light. If no ties are established for input 5, all output LEDs turn off.

								LED key:			= off,	= on
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12
1	2	3	4	5	6	7	8
			OUTPUTS
									F
1		3	4				8

Press	Press
F
RGBHV AUDIO
CONTROL	I/O
ENTER PRESET VIEW ESC	RGBHV AUDIO

Figure 3-11 — Example 4, step F: Viewing the current configuration, video-only

Muting and unmuting video and/or audio

Individual outputs can be muted or unmuted by doing the following:

1.	Press the Esc button to clear any input LEDs, output LEDs, or control LEDs
	that may be on.
2.	Press and release the View button.
3.	Select video, audio, or both to mute or unmute by pressing the RGBHV
	and/or Audio buttons.
4.	One at a time, press and hold the output button(s) for the desired output(s)
	for approximately 2 seconds. The output LED(s) for the selected output(s)

3-10 CrossPoint Matrix Switchers • Operation

Image 30

Contents CrossPoint Matrix Switchers CrossPoint 84, 88, 124, 128, 168, and 1616 HV and HVASicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start CrossPoint Matrix Switchers QS-1Quick Start CrossPoint Matrix Switchers, cont’d Table of Contents Table of Contents, cont’d One About the CrossPoint Series Matrix Switchers CrossPoint Matrix Switchers IntroductionIntroductiontroduction, cont’d Features Extron CrossPoint 128 HVAIntroduction, cont’d VCRCrossPoint Matrix Switchers Introduction Introduction, cont’d Two Power connection Installationstallation, cont’dRack Mounting the Switcher CrossPoint Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyInstallation, cont’d RS-232/422 connectionAdditional rear panel views Rear panel view, CrossPoint 84HV 11 Rear panel view, CrossPoint 124HVA 14 Rear panel view, CrossPoint 168HVA Installation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsCrossPoint Matrix Switchers Operation DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsOperation, cont’d ControlsFront panel I/O label windows Power Creating a configurationFront Panel Operations Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step D Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets Example 6 Save a presetViewing and adjusting the audio level HVA models only Example 7 Recall a presetExample 8 View and adjust an audio level = blinking value 1dB = on value 2dB = flash once 16 +8dB displayed, CrossPoint 168 System reset to factory defaults TroubleshootingFront panel security lockout executive mode Rear Panel ControlsGeneral checks Plasma display S-video problemWorksheets Worksheet example 1 Entering system equipment20 Worksheet example 2 Status meeting configuration Worksheet example 2 Drawing tiesWorksheet example 3 Test configuration System testOperation, cont’d Matrix Switchers Configuration Worksheet Input sources Output destinationsOperation, cont’d Four CrossPoint Matrix Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableCommand/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Resets Five Using the software Overview Matrix Switcher+ Control ProgramInstalling the software CrossPoint Matrix Switchers Matrix SoftwareExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusUsing the software Using emulation modeUsing the help system Button-Label GeneratorExtron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Matrix Switchers SpecificationsAudio audio models only Audio input audio models onlyAudio output audio models only Specifications, cont’d Part NumbersCables Extron Part BNC-5 Mini HR Cable AppendixBB ReferenceInformation,co t’d Hardware UpgradesOpening the switcher Opening the CrossPoint 84, 88, 124,CrossPoint Matrix Switchers Reference Information Opening the CrossPoint 168Closing the switcher Reference Information, cont’dSwapping the serial ports Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Replacing the AC fuse CrossPoint 84, 88, 124, and 128 onlyFigure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA