Extron electronic 1600 setup guide Configuration, Removing and Installing a Board or Blank Panel

Page 26

Configuration

Removing and Installing a Board or Blank Panel

NOTES:

For proper cooling and air flow, boards or blank panels should be installed in all locations during normal switcher operations.

The input and output boards are hot-swappable. You do not need to power down the switcher to remove and install a board.

Circuit boards can be added or removed to increase or decrease the I/O configuration (size) of the switcher. Remove and replace an I/O board or blank panel as follows:

1.For a board, disconnect any connected cables.

2.Rotate the left and right knurled knobs to completely loosen the captive screws.

3.Gently pull on the knurled knobs to loosen the board or panel from the backplane.

4.Slide the board or panel out of the chassis (see figure 12 on the next page).

ATTENTION: Do not touch the electronic components or the connectors on the backplane or on the circuit boards without being electrically grounded. Handle circuit boards by their edges only. Electrostatic discharge can damage circuits, even if you cannot feel, see, or hear it.

5.Place the removed board on an anti-static surface or in an anti-static container.

6.For a board, orient the board to be installed horizontally

(XTP CrossPoint 1600) or vertically (XTP CrossPoint 3200) and so that the IN or OUT silkscreen on the back panel is right side up.

7.For a board, align the board with the left and right chassis guides (above).

8.Gently slide the board or blank panel into the enclosure. For a board, slide it toward the front panel until it meets resistance.

9.For a board, gently seat the board in the backplane.

10.Use a screwdriver to tighten the left and right knurled knobs to lock the board or panel in place.

44 XTP CrossPoint 1600 and 3200 • Remote Control

XTP CrossPoint 1600 and 3200 • Configuration 45

Image 26
Contents XTP CrossPoint Conventions Used in this Guide Safety InstructionsFCC Class a Notice Notifications the following are usedContents About this Guide About the XTP CrossPoint Matrix SwitchersIntroduction Endpoint Configuration Swapping Boards and EndpointsRear Panel InstallationBoard Configuration Overview Inputs and Outputs 1b 1a 1c 1b 1a 1a XTP input connectors Connect a TP cable1f Audio local audio connectors Connect XTP CP 4i XTP input board2d RS-232/IR Over XTP connectors If desired Audio local audio connectors Connect2c 2b 2a 2a XTP output connectors Connect a TP cable XTP CP 4i DVI Pro DVI Pro input boardsPower Remote ControlReset XTP DTP 24/1000 Additional Connector InformationRJ-45 Connector XTP DTP 24P/1000RS-232 and IR Connector Wiring Pin FunctionFront Panel Primary and Redundant Power Supply LEDsFront Panel Operations Creating a TieSelecting Lock Mode 2 or Toggling Between Mode 2 and Mode Saving or Recalling a PresetSetting the Front Panel Locks Executive Modes Selected SIS Commands Remote ControlViewing and Adjusting the Audio Level Viewing Ties and Muting OutputsArrangement of Command and Response Tables Host-to-Switcher InstructionsCommon SIS Command Symbols Number of connections= RGB SIS Command and Response Table for Matrix Switcher CommandsIX! *X% Colr = Scart = YUVIX! *X% IX! *X% TintIX! *X% Brit EIX!*X%PHASInput audio selection Hdcp statusVideo mutes EIX!*X1!AFMTView video and audio mutes Audio output volumeAudio mutes XTP CrossPointSIS Command and Response Table for XTP T Hdmi Information requests1X*2X*3 ... X*n Pdif EX@*X2RELYInput video format available for endpoint input 1 only SIS Command and Response Table for XTP T USWAnalog input presets Horizontal shift available for endpoint input 1 onlySIS Command and Response Table for IP-Specific Commands IP and serial port setupIf the switcher is not password-protected , it checks XTP System Configuration ProgramAccessing the Html Pages Configuration Removing and Installing a Board or Blank PanelAlign with Plastic Guides Knurled Knobs Extron Warranty Extron Europe Extron India
Related manuals
Manual 2 pages 896 b