Extron electronic 1600 setup guide Endpoint Configuration, Swapping Boards and Endpoints

Table 1. Available Input and Output Boards

Input Boards	Output Boards
XTP CP 4i (twisted pair [TP] inputs)	XTP CP 4o (TP outputs)
XTP CP 4i HDMI (HDMI inputs)	XTP CP 4o HDMI (HDMI outputs)
XTP CP 4i DVI Pro (DVI Pro inputs)	XTP CP 4o DVI Pro (DVI Pro outputs)
	XTP CP 4o SA (stereo analog audio
	outputs)
XTP CP 4i VGA (universal analog inputs)

AV Control			Ethernet
Network	Ethernet	Ethernet	Extron
			TLP 1000TV
	Ethernet		10" Tabletop TouchLink
			Touchpanel

The XTP CrossPoint models are assembled from user-installed and hot-swappable input and output boards. Table 1, on the previous page, identifies the four types of input boards and four types of output boards currently available, each of which can receive (input boards) or output (output boards) up to four signals (see Inputs and Outputs on page 6 for details).

The XTP CrossPoint 1600 can support up to four input boards and four output boards of any of the type listed in table 1, for a total of 16 inputs and 16 outputs.

The XTP CrossPoint 3200 can support up to eight input boards and eight output boards of any of the type listed in table 1, for a total of 32 inputs and 32 outputs.

The matrix switcher can be remotely controlled via an Ethernet LAN port, serial port, or USB port connection using either the Extron XTP System Configuration Software or the Simple Instruction Set (SIS).

Endpoint Configuration

	Extron
Extron	XTP T USW 103
	Long Distance XTP
Cable	Switcher with
Cubby	Integrated XTP Transmitter
600	INPUTS
with AAPs VGA
	HDMI
	HDMI
	Ethernet

House

Network

Switch

+ - + - + - + -

	Ethernet
Extron
	RS-232Flat Panel
IPCP 505	Display
IP Link Control	HDMI
Processor

OUTPUTS

Extron

XTP SR HDMI

Long Distance XTP

In an XTP system, the transmitters connected to the input boards and the receivers connected to the output boards are known as "endpoints".

When you configure an XTP system (consisting of an

XTP CrossPoint Matrix switcher and its connected endpoints), connect a computer to the matrix switcher and configure the endpoints from the matrix switcher.

	Ethernet	RS-232
	CAT 5
Laptop HDMI
Ethernet
Extron	IN

IR Scaling Receiver

CAT 5 Ethernet

RS-232Flat Panel

Display

HDMI

Do not connect the computer directly to the endpoint for configuration when it is part of an XTP system.

Swapping Boards and Endpoints

XTP T UWP 202			1−4
			IN
Long Distance Two		INPUTS	5−8
			IN
Input XTP Transmitter CAT 5			9−12
			IN XTP		XTP	XTP	XTP
	HDMI with		13−16
	embedded
	Audio		OUT
			1−4
			OUT
Extron
		OUTPUTS	5−8
			OUT
AVT 200 HD	DVI		9−12
				XTP	XTP	XTP	XTP
			OUT
ATSC & HDTV			13−16
Cable Tuner		Extron

IN IN IN INOUT OUT OUT OUT

OUTPUTS			XTP R HDMI
+	-	+	-

	Extron
CAT 5	XTP R HDMI
	Long Distance XTP
HDMI	Receiver for HDMI

When you replace an input board, an output board, or an endpoint, the matrix switcher automatically applies the settings to the new device. If the stored settings are incompatible with the newly installed device, the matrix switcher applies a default configuration.

Blu-ray					XTP CrossPoint 1600
					Modular Digital
	HDMI		HDMI -
			DVI		Matrix Switcher
			Adapter
PC				CAT 5
		Ethernet
VGA					PC
Extron
XTP T VGA					VGA
Long Distance Universal

XTP Transmitter for VGA

Flat Panel

Display

Stereo Audio

XPA 1002

CLASS 2 WIRING

Extron	Extron
XPA 1002
	SI 28
Stereo Power Ampli￿er
	Surface
	Mount
	Speakers

Figure 1. Typical XTP CrossPoint Application

2 XTP CrossPoint 1600 and 3200 • Introduction XTP CrossPoint 1600 and 3200 • Introduction 3