XTP CP 4i DVI Pro (DVI Pro input boards)
IN | AUDIO | XTP CP 4i DVI Pro |
L | R | L | R | L | R | L | R | IN |
|
|
|
|
|
|
|
|
1g | 1g | 1g | 1g | 1h |
1g DVI connectors — Connect up to four DVI cables between these ports and the DVI output port of the digital video sources.
1h | Audio (local audio) connectors — Connect | L | R |
|
| ||
| balanced or unbalanced stereo audio inputs to these |
|
|
| 3.5 mm, |
|
|
| audio connectors on page 15 to wire the connectors). |
|
|
XTP CP 4i VGA (Universal analog video input boards)
IN | AUDIO | XTP CP 4i VGA |
L | R | L | R | L | R | L | R | IN |
|
|
|
|
|
|
|
|
1i | 1i | 1i | 1i | 1j |
1i VGA connectors — Connect up to four VGA cables between these ports and the analog audio output port of the video sources.
NOTE: | These universal analog video boards can accept RGB |
video and (with adapters) component video, | |
composite video (see Analog video connectors on page 15 | |
to wire the connectors for various analog video formats). | |
1j | Audio (local audio) connectors — Connect | L | R |
|
| ||
| balanced or unbalanced stereo audio inputs to these |
|
|
| 3.5 mm, |
|
|
| audio connectors on page 15 to wire the connectors). |
|
|
OUT | SIG LINK |
| PWR |
XTP
2b 2a
BOutput boards space — Make connections to installed output boards as desired.
XTP CP 4o (XTP output board)
SIG | LINK | SIG | LINK | SIG | LINK |
|
|
|
|
|
|
| XTP CP 4o | ||
PWR |
| PWR |
| PWR |
|
| IR | IR | IR | IR | OUT | ||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
LAN | XTP | LAN | XTP | LAN | XTP | LAN | Tx Rx | Tx Rx | Tx Rx | Tx Rx | Tx Rx | Tx Rx | Tx Rx | Tx Rx |
|
|
|
|
|
| |||||||||||
2c 2b 2a | 2c 2b 2a | 2c 2b 2a | 2c |
|
|
| 2d |
|
|
|
| ||||
2a XTP output connectors — Connect a TP cable | SIG |
| LINK | |||
| ||||||
between this connector and a compatible Extron |
|
|
|
|
|
|
PWR |
|
|
| |||
|
|
| ||||
XTP receiver (see TP connectors on page 12 to |
|
|
| |||
|
|
|
|
|
| |
wire the connector). |
|
|
| XTP | ||
2b XTP Power indicators — Light or blink to indicate the status of the power over XTP that the output board is providing to the receiver endpoint as follows:
Lit green — The board is providing XTP power to the endpoint.
Lit amber — XTP Power is available for the endpoint, but it is disabled in the matrix switcher.
Flashing amber — No XTP power is available for the endpoint, but it is enabled in the matrix switcher.
Lit red — A wiring fault exists.
Unlit — The endpoint is not capable of receiving power over XTP.
2c LAN connectors — As desired, connect a TP cable between a host device or control LAN and this
connector for passive extension to the LAN (Ethernet) 
LAN 
connector on the connected endpoint (see TP
connectors on page 12 to wire the connector).
2d | IR | |
|
| |
connect serial |
|
|
or both to these 3.5 mm, | Tx Rx | Tx Rx |
|
|
connectors for bidirectional
communications on the associated inputs (see
8 | XTP CrossPoint 1600 and 3200 • Installation | XTP CrossPoint 1600 and 3200 • Installation | 9 |