Tripp Lite APS1024INT Hardwired Electrical Connections, AC Input Electrical Connection

Page 9

Hardwired Electrical Connections

(All hardwire models)

(See Diagram 3, p. 33).

Consult a qualified electrician and follow all applicable electrical codes and requirements.

HARDWIRE PROCEDURE

1)Loosen screws and remove cover plate from your APS's Hardwire AC electrical box. Remove the knockout covers closest to the desired electrical source and to your equipment.

2)Thread your wires through strain reliefs and through the knockouts.

3)Connect both input and output ground wires to the ground (green) terminal.

4)Connect the incoming hot wire to the input hot (brown) terminal.

5)Connect the incoming neutral wire to the input neutral (blue) terminal.

6)Connect the outgoing hot wire to the output hot (black) terminal.

7)Connect the outgoing neutral wire to the output neutral (white) terminal.

8)Tighten and affix strain reliefs. Replace cover plate and tighten screws.

AC Input Electrical Connection

(All corded models)

Plug the line cord into an outlet providing 208V or 230V power at 50 Hz. (A trained technician may be able to convert a unit to receive 60 Hz power. Consult Tripp Lite.) If an adaptor must be used, use one that maintains the APS's ground connection. Make sure that the circuit you connect your APS to has adequate overload protection, such as a circuit breaker or a fuse.

AC Output Electrical Connection

(All corded models)

Simply plug your equipment into the unit's AC receptacles. If adaptors are necessary, use adaptors that provide a ground connection.

Set Operating Mode Switch

•Switch to “AUTO/REMOTE” when you are using connected equipment. ADVANTAGE: Uninterruptable power supply: provides battery backup power during blackouts or brownouts.

Note: When the switch is in the "AUTO/REMOTE" position, you can operate a user- supplied Remote Connector to transfer between battery-backup and charge-only modes. (See Remote Connector manual for more information.)

•Switch to “CHARGE ONLY” when you are not using connected equipment. (WARNING! APS will not provide battery backup!) ADVANTAGES: A) Continues to charge battery when power is present, and B) Turns OFF the APS’s inverter, preventing battery drain during blackouts or brownouts.

•Switch to “OFF” to completely turn off the APS and connected equipment or to reset the APS after it has shut down due to overload or overheating.

9

9906058 230V APS MV-cabinet--English.p65 9

 

 

 

3/21/00, 4:29 PM

Page 8 Page 10
Image 9
Page 8 Page 10
Contents APS 3636VRI Configuration & Connection pIntroduction Voltage Regulation Select models only Advanced, 3-Stage Battery ChargerLoad Sharing Select models only Frequency-Controlled Inverter OutputBattery Connection Warnings SafetyAPS Location Warnings Equipment Connection WarningsDIP Switch Group a All models ConfigurationSelect Battery Type Select High AC Switch To Battery Voltage PointDIP Switch Group B Available on Select Models Equalize Battery ChargeLoad Sharing Selecting Battery Type Battery SelectionSelecting Battery Amp Hour Capacity Permanent Mounting OptionalBattery Connection DC Vehicular Battery Connection StandardUse the Shortest and Heaviest Gauge battery cabling AC ConnectionSet Operating Mode Switch Hardwired Electrical ConnectionsSee Diagram 3, p AC Input Electrical ConnectionSwitches, Indicator Lights Other Features SwitchesIndicator Lights Other Features Limited Warranty Maintenance & ServiceMaintenance ServiceSymptom Problems Corrections TroubleshootingInverter Specifications-Corded ModelsSpecifications-Hardwired Models Configuración y Conexión p Introducción Regulación Automática de Voltaje Modelos Selectos Solamente Cargador Avanzado De 3 Etapas para BateríasCompartición de Carga Modelos selectos solamente Inversor con Salida de Frecuencia ControladaPrecauciones sobre la Ubicación del APS SeguridadPrecauciones Sobre la Conexión de Baterías Precauciones Sobre la Conexión de EquiposSeleccione el Tipo de Baterías ConfiguraciónCompartición de Carga Grupo B DE Interruptores DIP Modelos SelectosIgualar la Carga de Baterías Selección de BateríasSeleccione la Capacidad en Amperios/Hora de las Baterías PasoVea el Diagrama 2 en la página Escoja la configuración apropiada a sus bateríasInstalación Permanente Opcional Conexión de Baterías EstándarConexión de Baterías DC Vehículos Conexión de CAConexiones Eléctricas Directas al Circuito Regule el Interruptor Operating Mode Modo de Operación Conexión de la Entrada Eléctrica de CAConexión de la Salida Eléctrica de CA Luces Indicadoras InterruptoresLuz Indicadora Capacidad Otras CaracterísticasTerminales de Entrada de CD Todos los modelos Conector para el Módulo de Control Remoto Todos los modelosServicio en México MantenimientoServicio Garantía Limitada Resolución de Problemas Inversor EspecificacionesModelos CON Toma Directa AL Circuito APS2424 INT APS3636 VRI Diagrams/Esquemas Volts 12V 93-1425 9906057 03/00
Top Page Image Contents