Moxa Technologies AWK-1100, MOXA AirWorks Regulatory Statement, TTE Compliance Statement

Page 47

C

Regulatory Statement

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

yReorient or relocate the receiving antenna.

yIncrease the separation between the equipment and receiver.

yConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.

yConsult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, (example – use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity (R&TTE).

The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) as of April 8,2000.

Page 46 Page 48
Image 47
Page 46 Page 48
Contents First Edition, July Moxa AirWorks AWK-1100 User’s ManualDisclaimer Copyright NoticeTrademarks Table of Contents Page Introduction Overview Package ChecklistProduct Features Product SpecificationsMechanical Page Getting Started ‰ Confirming the Settings of the AP and Client ComputersFirst-Time Installation and Configuration AP Client Select the Operational Mode for AWK-1100AP/Bridge Review and Apply Settings Configure AWK-1100’s Ieee 802.11 settingsConfiguring Ieee 802.11g-related Settings Deploying the Access Point APSetting up Client Computers Checking if the Ieee 802.11g-related Settings Work Confirming the Settings of the AP and Client ComputersConfiguring TCP/IP-related Settings To check if a client computer can assess the Internet Checking if the TCP/IP-related Settings WorkPage ‰ Viewing Status Web Console ConfigurationMenu Structure Home and Refresh Buttons Save, Save & Restart, and Cancel ButtonsSystem Log Associated Wireless ClientsViewing Status Current Dhcp MappingsSTA-AP Link Monitor AP Client mode onlySpecifying the Operational Mode General OperationsAP/Bridge AP Client Administrative PasswordManaging the Firmware Upgrading Firmware by HttpUpgrading Firmware by Tftp Backing up and Restoring Configuration Settings by HttpChoose Tftp as the Firmware management protocol Backing up and Restoring Configuration Settings by Tftp Addressing Configuring TCP/IP-related SettingsResetting the Configuration to Factory Defaults Static Dhcp Mappings Dhcp Server AP/Bridge modes onlyBasic Link Integrity Configuring Ieee 802.11g-related SettingsCommunication AP Load Balancing Wireless Distribution SystemAssociation Control Sample wireless bridge network topology Security STA Shared Key , and Auto Set the Access control type to inclusive MAC-Address-Based Access ControlSet the Access control type to exclusive Click Download Ieee 802.1X/RADIUS AP mode onlyInternet IP Protocol Filters Configuring Advanced SettingsPacket Filters Ethernet Type FiltersSystem Log ManagementTCP/UDP Port Filters UPnPSnmp Page Default Settings Snmp write community LAN InterfaceManagement Snmp read communityWireless client computer cannot associate with an AWK-1100 TroubleshootingWireless Settings Problems AP does not respond to ping from the client computer TCP/IP Settings ProblemsUnknown Problems Moxa AirWorks AWK-1100 User’s Manual TTE Compliance Statement Regulatory StatementFederal Communication Commission Interference Statement Moxa AirWorks AWK-1100 User’s Manual Regulatory Statement Service Information Following services are provided Moxa Internet ServicesMoxa Product † AWK-1100-US † AWK-1100-EU Serial Number Problem Report FormProduct Return Procedure
Top Page Image Contents