Moxa Technologies AWK-1100, MOXA AirWorks user manual Shared Key , and Auto

Page 33

MOXA AirWorks AWK-1100 User’s Manual

Web Console Configuration

A total of 7 security modes are available with the different AWK-1100 models:

yOpen System. No authentication, no data encryption.

yStatic WEP. WEP (Wired Equivalent Privacy) keys must be manually configured.

yStatic TKIP (WPA-PSK).Only TKIP (Temporal Key Integrity Protocol) mechanism of WPA (Wi-Fi Protected Access) is enabled. In this mode, you need to specify the Pre-shared key, which will be used by the TKIP engine as a master key to generate keys that actually encrypt outgoing packets and decrypt incoming packets.

NOTE

The number of characters of the Pre-shared key setting must be at least 8 and can be up to 63.

 

 

yIEEE 802.1X EAP without Encryption (EAP-MD5). The IEEE 802.1X functionality is enabled and the user-name/password-basedEAP-MD5 authentication is used. No data encryption.

yIEEE 802.1X EAP with Static WEP (EAP-MD5).The IEEE 802.1X functionality is enabled and the user-name/password-based EAP-MD5 authentication is used. Data encryption is achieved by static WEP.

yIEEE 802.1X EAP with Dynamic WEP (EAP-TLS, EAP-TTLS, PEAP). The IEEE 802.1X functionality is enabled and dynamic WEP key distribution authentication (EAP-TLS,EAP-TTLS, or PEAP) is used. Data encryption is achieved by dynamic WEP.

yIEEE 802.1X EAP with Dynamic TKIP (WPA). This is a full WPA mode, in which both the TKIP and IEEE 802.1X dynamic key exchange mechanisms are enabled. The AP is highly secure in this mode.

 

In the above security modes, a back-end RADIUS (Remote Authentication Dial-In User Service)

 

server is needed if IEEE 802.1X functionality is enabled. See Section 0 for more information

 

about IEEE 802.1X and RADIUS.

 

According to the IEEE 802.11 standard, WEP can be used for authentication and data encryption.

 

Normally, Shared Key authentication is used if WEP data encryption is enabled. In rare cases,

 

Open System authentication may be used when WEP data encryption is enabled. The

 

Authentication algorithm setting is provided for better compatibility with wireless clients with

 

various WLAN network adapters. There are three options available, including Open System,

 

Shared Key, and Auto.

 

When WEP is enabled by a security mode, the Key length can be specified to be 64 Bits or 128

 

Bits. The Selected key setting specifies the key to be used as a send-keyfor encrypting traffic

 

from the AP side to the wireless client side. All 4 WEP keys are used as receive-keysto decrypt

 

traffic from the wireless client side to the AP side.

 

 

NOTE

Each field of a WEP key setting is a hex-decimalnumber from 00 to FF. For example, when the

 

security mode is Static WEP and the key length is 64 Bits, you could set Key 1 to

 

“00012E3ADF”.

 

 

3-17

Image 33
Contents First Edition, July Moxa AirWorks AWK-1100 User’s ManualCopyright Notice TrademarksDisclaimer Table of Contents Page Introduction Product Features Package ChecklistProduct Specifications OverviewMechanical Page Getting Started ‰ Confirming the Settings of the AP and Client ComputersFirst-Time Installation and Configuration Select the Operational Mode for AWK-1100 AP/BridgeAP Client Review and Apply Settings Configure AWK-1100’s Ieee 802.11 settingsDeploying the Access Point AP Setting up Client ComputersConfiguring Ieee 802.11g-related Settings Confirming the Settings of the AP and Client Computers Configuring TCP/IP-related SettingsChecking if the Ieee 802.11g-related Settings Work To check if a client computer can assess the Internet Checking if the TCP/IP-related Settings WorkPage ‰ Viewing Status Web Console ConfigurationMenu Structure Home and Refresh Buttons Save, Save & Restart, and Cancel ButtonsViewing Status Associated Wireless ClientsCurrent Dhcp Mappings System LogSpecifying the Operational Mode Link Monitor AP Client mode onlyGeneral Operations STA-APManaging the Firmware Administrative PasswordUpgrading Firmware by Http AP/Bridge AP ClientUpgrading Firmware by Tftp Backing up and Restoring Configuration Settings by HttpChoose Tftp as the Firmware management protocol Backing up and Restoring Configuration Settings by Tftp Configuring TCP/IP-related Settings Resetting the Configuration to Factory DefaultsAddressing Dhcp Server AP/Bridge modes only BasicStatic Dhcp Mappings Configuring Ieee 802.11g-related Settings CommunicationLink Integrity Wireless Distribution System Association ControlAP Load Balancing Sample wireless bridge network topology Security STA Shared Key , and Auto MAC-Address-Based Access Control Set the Access control type to exclusiveSet the Access control type to inclusive Click Download Ieee 802.1X/RADIUS AP mode onlyInternet Packet Filters Configuring Advanced SettingsEthernet Type Filters IP Protocol FiltersTCP/UDP Port Filters ManagementUPnP System LogSnmp Page Default Settings Management LAN InterfaceSnmp read community Snmp write communityTroubleshooting Wireless Settings ProblemsWireless client computer cannot associate with an AWK-1100 AP does not respond to ping from the client computer TCP/IP Settings ProblemsUnknown Problems Moxa AirWorks AWK-1100 User’s Manual Regulatory Statement Federal Communication Commission Interference StatementTTE Compliance Statement Moxa AirWorks AWK-1100 User’s Manual Regulatory Statement Service Information Following services are provided Moxa Internet ServicesMoxa Product † AWK-1100-US † AWK-1100-EU Serial Number Problem Report FormProduct Return Procedure